Consider a carnot refrigeration cycle with a working fluid

Assignment Help Mechanical Engineering
Reference no: EM13629699

Consider a Carnot Refrigeration cycle with a working fluid of R-134a operating between temperatures of -10oC and 20oC. The compressor in the cycle requires 500 W of power.

a) What is the maximum coefficient of performance?

b) What is the rate of heat that is removed from the refrigerated space?

c) What is the rate of heat that is rejected from the cycle?

d) The R-134a enters the evaporator as a saturated mixture with a quality of 0.1. If the R-134a leaves the evaporator as a saturated mixture with a quality of 0.9 what is the flow rate?

 

 

Reference no: EM13629699

Previous Q& A

  A package is being vibrated on a vibration table

a package is being vibrated on a vibration table. accelerometers attached to the the table and the product measure

  Cylinder conditions at the start of compression in an si

cylinder conditions at the start of compression in an si engine operating at wot on an air-standard otto cycle are 60

  A 200-in diameter rod 15 ft long elongates 012 in under a

a 2.00-in diameter rod 15 ft long elongates 0.12 in under a load of 60 kip. the diameter of the rod decreases 0.0004 in

  Water vapor is cooled in a closed rigid tank from 520c and

water vapor is cooled in a closed rigid tank from 520c and 100 bar to a final temperature of 270c. determine the final

  What is the work done under the isothermal compression vi

consider a 3-dimensional ideal gas of n particles at temperature ti with an initial volume vi. you adiabatically

  384 knowing that the stepped shaft shown tranmits a torque

3.84 knowing that the stepped shaft shown tranmits a torque of magnitude t2.50 kipin determine the maximum shearing

  Find the elapsed time to vaporize the propane and total

a factory has a large liquid propane storage tank. the propane is to be used as vapor. evaporation of the liquid

  For the variable length of hospital stay determine the

n the article a multifactorial intervention program reduces the duration of delirium length of hospitalization and

  Steam flows steadily through an adiabatic turbine the inlet

steam flows steadily through an adiabatic turbine. the inlet conditions of the steam are 10 mpa 450 ordmc and 80 ms and

  Announcing contract award and responsibilities of the

imagine that you are working on a project to purchase 5000 electrical generators with an electrical capacity of three 3

Reviews

Write a Review

 

Similar Q& A

  In a design test of penetration resistance a 12-gram bullet

in a design test of penetration resistance a 12-gram bullet is fired through a 400-mm stack of fibrous plates with an

  Determine the required diameter for the uniaxial tensile

determine the required diameter for the uniaxial tensile loaded two-force component if the failure criterion is

  The upside-down steel a frame shown in the figure is to be

the upside-down steel a frame shown in the figure is to be bolted to steel beams on the ceiling of a machine room using

  The pressure acting on a 125 in2 test specimen equals 15

the pressure acting on a 1.25 in2 test specimen equals 15 mpa. what is the force in n acting on the specimen expressed

  The maximum compression of the springs is to be 2m

two equal-length springs are nested together in order to form a shock absorber. if it is designed to arrest the motion

  The evaporator operates at 200 kpa determine the systems

a heat pump uses r-134a as the working fluid and operates on an ideal vapor-compression cycle. the condenser pressure

  The time is determined according to the level of the water

a water clock clepsydra used in ancient greece is designed as a vessel with a small orific o. the time is determined

  An ideal diesel cycle with air as the working fluid has a

an ideal diesel cycle with air as the working fluid has a compression ratio of 20 and a cutoff ratio of 1.3. this cylce

  If the maximum axial stress allowed in the wood piles is 51

at a local marina the dock is supported on wood piling in the manner . the top part ab of one pile is above the normal

  If it is thrown downward released it at 3 ft above the

when a ball is released from rest at a height of 5 ft above the floor it bounces to a height of 3.5 ft. if it is thrown

  A knoop microhardness measurement was made on a sample

a knoop microhardness measurement was made on a sample that resulted in a khn of 481when a load of 5120 kg was applied.

  A steam turbine is operated ith an input temp of 800c and

a steam turbine is operated ith an input temp of 800c and exhaust temp of 150c. what is the maximum amount of work the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd