Consider a 1000-w iron whose base plate is made of

Assignment Help Mechanical Engineering
Reference no: EM13632026

Consider a 1000-W iron whose base plate is made of 0.5-cm-thick aluminium alloy 2024-T6 (p=2771 kg/m^3) and Cp= 875 J/(kg C). The base plate has a surface area of 0.03 m^2. Initially, the iron is in thermal equilibrium with the ambient air at 22 degree C. Assuming 85 percent of the heat generated in the Resistance wires is transferred to the plate, determine the minimum time needed for the plate temperature to reach 140.

Reference no: EM13632026

Questions Cloud

A monatomic gas at a pressure of 12 kpa and volume 1 m3 : a monatomic gas at a pressure of 12 kpa and volume 1 m3 undergoes a thermodynamic cycle described by three processesi
How would the natural frequency be analyzed assume that the : a cantilevered steel pipe tower 80 m tall is being considered for a new wind turbine. the weight of the turbine is 3400
Let w1 and w2 be independent geometric random variables : let w1 and w2 be independent geometric random variables with parameters 0.2 and 0.4.
Estimate the average life expectancy in the united states : the average life expectancy in the united states l has been rising steadily over the past few decades as shown in the
Consider a 1000-w iron whose base plate is made of : consider a 1000-w iron whose base plate is made of 0.5-cm-thick aluminium alloy 2024-t6 p2771 kgm3 and cp 875 jkg c.
A block on a spring is pulled ot the right and released at : a block on a spring is pulled ot the right and released at t 0 s.it passes x 3.1cm at t 0.685s and it passes x
Take into account that some of the oxygen is lost to the : image text transcribed for accessibility write the combustion equation for the complete combustion of methane in a
A gas turbine for an automobile is designed with a : a gas turbine for an automobile is designed with a regenerator. air enters the compressor of this engine at 100 kpa and
Additionally a random sample of 1000 registered voters in : 1. a candidate for one of ohios two u.s. senate seats wishes to compare her support among registered voters in the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  For each process of a closed system show the initial and

for each process of a closed system show the initial and final states on a properly-labeled t-s diagram evaluate the

  A mass of 3 kilograms of steam at 2 mpa and 250degc are

a mass of 3 kilograms of steam at 2 mpa and 250degc are contained in a rigid tank. how much heat must be removed from

  A piston-cylinder assembly contains 2 lb of water initially

a piston-cylinder assembly contains 2 lb of water initially at 300degf. the water undergoes two processes in series

  At the same time measurements showed that the pipe

during drilling of a deep oil well the drill pipe got rigidly stuck. it was necessary to determine the depth at which

  A particle of mass m is projected from point a with an

a particle of mass m is projected from point a with an initial velocity v0 perpendicular to line oa and moves under a

  A quantity of steam the original pressure and volume being

a quantity of steam the original pressure and volume being 140 knm2 and 150 litres respectively is compressed to a

  Determine the centerline temperature of the beam after an

a cylindrical stone mix concrete beam of diameter d 0.45 initially at ti 20c is exposed to hot gases at tinfinity

  If the scrubber removes 92 molar basis of the entering h2s

a flue gas is which the mole fraction of h2s is 0.002 enters a scrubber operating at steady state at 200 deg f 1 atm

  Air enters a set of these nozzles at 215 psia and 700

the stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically.

  Let the weight be pulled down 3 in below the equilibrium

a spring is stretched in 1.5 in. by a 4 lb weight. let the weight be pulled down 3 in. below the equilibrium level nd

  For each of the following cases determine the internal

for each of the following cases determine the internal energy and the enthalpy using the compressed liquid tables and

  Assuming cold air standard assumptions for a spark ignition

assuming cold air standard assumptions for a spark ignition engine cycle otto and given the following data compression

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd