Conduct vibration monitoring of centrifugal blower

Assignment Help Mechanical Engineering

Reference no: EM131469243

You need to write the abstract for the experiment and not more then 700 words.

Vibration Monitoring of Centrifugal Blower Set-up - Misalignment, Looseness, and Unbalance

Aim and objectives

1.1 Aim:

The aim of this experiment is to conduct vibration monitoring of centrifugal Blower set-up and capture and analyse the different waveforms in time-domain and frequency domain associated with the following faults such as misalignment of shafts, looseness and unbalance of fan impeller.

The set-up uses accelerometer sensor, data acquisition unit DAQ, LABVIEW software to display the waveforms.

1.2 Objectives:

- To run the centrifugal blower set-up and capture vibration signals and and waveforms

- To simulate misalignment, looseness and unbalance fault in the machine and take the vibration signals or waveforms

- To identify the specific signature of misalignment, looseness and Unbalance fault in the FFT spectrum

Theoretical background

Vibration Monitoring is generally the key component of most condition monitoring techniques. Almost all machine vibrate, and the link between these vibrations and the machine condition is both easily measured, and the results easily interpreted.

Vibration Monitoring reveals 70 - 80% of the mechanical problems associated with the machine. It is normally applied by using transducers to measure, acceleration, velocity, or displacement. The choice of these depends on the frequency of the vibration, acceleration: 0-20 kHz, velocity: 2Hz to 2kHz, displacement: 0-200Hz. There are various techniques of Vibration Monitoring. Time Domain method -Overall readings raw signal from the transducer circuitry (sensor) and obtaining the peak, peak-to-peak or RMS values of the signal. Using standard charts, the condition of the machine can be assessed. Frequency Domain method -Fast Fourier Transform (FFT)

A technique of changing time domain signal (original signal) into frequency domain (spectrum) where frequency information would be presented and this method supports in determining location of faults. Time-Frequency Domain Method-Wavelet Transform.

A powerful multi-resolution method that both time and frequency information are presented where a small wave known as mother wavelet function used using parameters of scaling and shifting .

3.2 Procedure
- Turn the electrical switch for the panel of the centrifugal blower as shown.
- From the control panel, turn ON motor and and speed control.
- Be sure that there are no tools or any obstruction in the machine before turning ON.
- Turn on the Data Acquisition Unit DAQ and the computer
- Open the LABVIEW software in the computer
- Position the accelerometer in the bearing housing as shown in the figure
- Be sure that the cable of the accelerometer in safe from the turning shaft and coupling
- Take a reading in time and frequency domain.

Attachment:- Experiment Vibration Monitoring of Centrifugal Blower.rar

Reference no: EM131469243

Questions Cloud

Outline a marketing strategy for the health care provider : Outline a marketing strategy for the health care provider you selected. Determine the direct impact of marketing for the health care provider you selected.

What are the four guidelines to getting feedback on messages : Which personality traits are associated with being closed to feedback? What are the four guidelines to getting feedback on messages?

Would you like to work in the airline industry : Would you like to work in the airline industry? If you had a job with an airline, what would be the best jib for you, suiting your personality and abilities?

What should be included in your plan to send a message : What should be included in your plan to send a message? What are the three parts of a written outline?

Conduct vibration monitoring of centrifugal blower : Write the abstract for the experiment and not more then 700 words - Vibration Monitoring of Centrifugal Blower Set-up

What are the benefits of a corporate leadership strategy : McDonald's has achieved the status of one of the most recognizable franchises across the globe through a mixture of successful marketing, consistent service.

Why the communication skills used within a business unit : The decision to dedicate the resources needed to fund and support the Department of Communications within Navistar International sends a signal that corporate.

What are the differences between in-groups and outgroups : What are the differences between in-groups and outgroups? How do quality leader-member exchange relationships influence follower behavior?

What are the three stages of life-cycle model of lmx theory : What are the three stages of the life-cycle model of LMX theory? How can a follower's perception or attribution of a leader influence their relationship?

Reviews

len1469243

4/21/2017 2:09:51 AM

please could you help in my lab experiment I just need to write the abstract for the experiment 1 & 2 & 3 for one page I guess not more then 700 word's each tutor have to read the ( aim + Objectives + Theoretical background + Apparatus Set up + Procedure ) to start writing the abstract in each experiments The aim of this experiment is to conduct vibration monitoring of centrifugal Blower set-up and capture and analyse the different waveforms in time-domain and frequency domain associated with the following faults such as misalignment of shafts, looseness and unbalance of fan impeller.

Write a Review

Required(*) Message

User Account

All Pages