Compute the lateral deflections of the frame

Assignment Help Mechanical Engineering

Reference no: EM131513630

Question: Computer study of the behavior of multistory building frames. The object of this study is to examine the behavior of building frames fabricated with two common types of connections. When open interior spaces and future flexibility of use are prime considerations, building frames can be constructed with rigid connections usually fabricated by welding. Rigid joints (see Figure P7.47b) are expensive to fabricate and now cost in the range of $700 to $850 depending on the size of members. Since the ability of a welded frame to resist lateral loads depends on the bending stiffness of the beams and columns, heavy members may be required when lateral loads are large or when lateral deflections must be limited. Alternately, frames can be constructed less expensively by connecting the webs of beams to columns by angles or plates, called shear connections, which currently cost about $80 each (Figure P7.47c). Also see Photo 5.1 for the rigid and shear connections. If shear connections are used, diagonal bracing, which forms a deep vertical truss with the attached columns and floor beams, is typically required to provide lateral stability (unless floors can be connected to stiff shear walls constructed of reinforced masonry or concrete).

Properties of Members

In this study all members are constructed of steel with E = 29,000 kips/in.2

All beams: I = 300 in.4 and A = 10 in.2

All columns: I = 170 in.4 and A = 12 in.2

Diagonal bracing using 3-in. square hollow structural tubes (Case 3 only-see dashed lines in Figure P7.47a), A = 3.11 in.2 , I = 3.58 in.4.
Using the RISA-2D computer program, analyze the structural frames for gravity and wind loads in the following three cases.

Case 1 Unbraced Frame with Rigid Connections

(a) Analyze the frame for the loads shown in Figure P7.47a. Determine the forces and displacements at 7 sections along the axis of each member. Use the computer program to plot shear and moment diagrams.

(b) Determine if the relative lateral displacement between adjacent floors exceeds 3 /8 in.-a limit specified to prevent cracking of the exterior façade.

(d) Note the difference between the magnitudes of the vertical and lateral displacements of joints 4 and 9. What are your conclusions?

Case 2 Unbraced Frame with Shear Connections

(a) Repeat steps a, b, and c in Case 1, assuming that the shear connections act as hinges, that is, can transmit shear and axial load, but no moments.

(b) What do you conclude about the unbraced frame's resistance to lateral displacements?

Case 3 Braced Frame with Shear Connections
As in case 2, all beams are connected to columns with shear connectors, but diagonal bracing is added to form a vertical truss with floor beams and columns (see dashed lines in Figure P7.47a)

(a) Repeat steps a, b, and c in Case 1.

(b) Compute the lateral deflections of the frame if the area and moment of inertia of the diagonal members are doubled. Compare results to the original lighter bracing in (a) to establish the effectiveness of heavier bracing.

(c) Make up a table comparing lateral displacements of joints 4 and 9 for the three cases. Discuss briefly the results of this study.

2302_7.47.png

Reference no: EM131513630

Questions Cloud

What is the minimum required moment of inertia : The rigid jointed steel frame with a fixed base at support A has to carry both the dead and live loads shown in Figure P7.46. Both the column and the girder.

The interview and communication techniques : Description of the interview and communication techniques you would use with your selected patient. Explain why you would use these techniques.

What is equilibrium expected growth rate : What is the equilibrium expected growth rate?

What is the companys current stock price : What is the company’s current stock price, P0?

Compute the lateral deflections of the frame : Computer study of the behavior of multistory building frames. The object of this study is to examine the behavior of building frames fabricated.

More desirable addition to portfolio then stock : Stock A would be a more desirable addition to a portfolio then Stock B. When held in isolation, Stock A has less risk than Stock B.

What is expected return on the portfolio : What is the expected return on the portfolio if it holds 12,500 shares of stock C, 12,000 shares of stock A,

Describe the role and responsibilities of the administration : Describe the various government & private resources available that assist in developing and maintaining quality improvement programs in your chosen facilities.

Compute both displacement of given joint : For the truss in Figure, compute the horizontal and vertical components of displacement of joint B produced by the 100-kip load.

User Account

All Pages