Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
• You are considering which amplifier class to use for an AM aircraft transceiver that has an output power of 10 watt and uses 24 V for power. Assuming that the transmitter consumes 50% of the overall energy used by the transceiver, while the receiver and other circuitry consumes the rest, compare the average power requirement in watt-hours using a Class A, Class AB, and Class C amplifier. The Class C amplifier operates with a conduction angle of ?/6. Assume the Class A and Class AB amplifiers attain their maximum possible efficiency. Note: the Class C amplifier would not be suitable for modulated AM. For this class amplifier, the Class C amplifier would be used to generate the RF and a separate amplifier would be used to generate audio that would modulate the RF. This technique is know as "plate-modulation" for vacuum tubes, "collector-modulation" for bipolar junction transistors or "drain-modulation" for field effect transistors.
• Compute the power levels of the 2nd, 3rd, and 4th harmonics relative to the fundamental output signal for the Class C amplifier. (Hint: compute the Fourier coefficients for the harmonics of the clipped sinusoid that results from the partial conduction angle of the amplifier).
Efficiency of MOSFET circuit provide in datasheets of any product is measured at transient state of my output node or staedy state?
1. Express the Boolean function f(X,Y,Z) = XY + X(Y + Z) in sum of products form showing the sum all nonzero minterms. 2. Express the Boolean function f(A,B,C,D) = A(B + BC) + ACD in sum of products form showing the sum all nonzero minterms.
Plot the magnitude response (in dB) and the impulse response of the designed filter using MatLab.
The load on a 460-V, 60-Hz, Y-connected, balance three-phase source consists of three equal Y-connected impedances of 100+j100 ohms, and three equal Delta-connected impedances of 300-j300 ohms. Compute the line current, power, and power factor for..
A saturated npn transistor has a base to emitter applied voltage of 0.6V. The collector to emitter voltage is 0.2V. The collector current is 12mA
A chopper is used to control the power flow from a dc source voltage of 125-V to a battery whose voltage is 240-V. The power transferred is 60 kW. Determine the duty cycle and the average input current.
Design a PD Controller G_c(s) = K_p + K_d*s using the root-locus method such that the closed-loop system has a damping ratio, zeta = 0.7 and a natural frequency, omega_n = 0.5 rad/sec.
A 10m diameter cylindrical tank is emptied by a constant outflow of 1 m3 /min. A two position controller is used to open and close a fill valve with an open flow of 3 m3 /min. For level control the neutral zone is 1m and the setpoint is 10m.
Suppose the information portion of a packet contains 10 bytes consisting of the 8- bit unsigned binary ASCII representation of string "Link Layer".
Draw a relay construction diagram and briefly explain the operation of a relay.
Write a main program to call a procedure that converts the Fahrenheit temperature value stored in the location labeled TdegF to its Celsius equivalent. The range of temperatures is 32F to 212F. The procedure stores the converted temperature in loc..
The line is terminated in a load RL = 25 ohm. Use the bounce diagram to plot V(t) at a point midway along the length of the line from t = 0 to t = 25 ns.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd