Compute the first energy level

Assignment Help Mechanical Engineering
Reference no: EM13704702

Compute the first energy level (in eV) for a particle trapped in a 0.1 nm region. Assume the mass of the particle is equal to 0.511 MeV/c^2

Reference no: EM13704702

Questions Cloud

Determine the width w of the link bc : Determine the width w of the link BC needed so that the structure with load P = 20 kips has a factor of safety equal to 2.5. Link BC is ½ in thick and has a 85 ksi ultimate strength in tension.
Heat is transferred to the water until the pressure increase : A piston cylinder device contains 8.00 kg of water at an initial pressure of 200 kPa. Initially the piston is at rest on a set of stops and the initial volume is 2.00m3. Heat is transferred to the water until the pressure increases to 1000 kPa when t..
A fan accelerates air : A fan accelerates air (at atmospheric pressure and 300K) from a rest to 5m/s. The fan mass flow rate of air is 1.2 kg/s. What is the minimum amount of power this fan must consume to operate under these conditions?
What is the likely response from the board members : What are the issues that you will take into account and what is the likely response from the board members?
Compute the first energy level : Compute the first energy level (in eV) for a particle trapped in a 0.1 nm region. Assume the mass of the particle is equal to 0.511 MeV/c^2
Determine the atomic packing factor : Determine the atomic packing factor (APF) of the simple hexagonal crystal structure assuming the lattice parameter a is equal to 2R and the lattice parameter c is equal to 1.5 a. The Bravais lattice is shown below. Assume one atom on each lattice poi..
Elevator to the third floor of a parking garage : A car is to be hoisted by elevator to the third floor of a parking garage, which is 36 ft above the ground. If the elevator can accelerate at 0.7 ft/s2, decelerate at 0.2 ft/s2, and reach a maximum speed of 8 ft/s, determine the shortest time to make..
Volatility of demand on your service delivery system : Assume that the volatility of demand on your service delivery system is much higher than that on your manufacturing production system. Your management has indicated that the anticipated inventory storage will smooth the demand in manufacturing,..
Needing a tutor to help writing punitive damages promote : Needing a tutor to help writing punitive damages promote injustice to society and that tort reform is needed. Needing a cover page, table of contents, introduction, highlight of punitive damages and its injustice to the society, case analysis, ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The heat addition in both combustion chambers is reduced

a gas turbine operates with a regenerator and two stages of reheating and intercooling. this system is designed so that

  The engine is used to drive an electrical generator that is

1. an aluminum casting that weighs 10 pounds sits on a steel surface. how much force will be necessary to get it to

  If the wall and air of the room are at 295 what is the net

a flat isothermal heating panel 0.5 m wide by 0.8 m high is mounted to one wall of a large room. the surface of the

  A room in the lower level of a cruise ship has a 30cm

a room in the lower level of a cruise ship has a 30cm diameter circular window.if the midpoint of the window is 4m

  The condenser operates at 14 mpa if the mass flow rate of

a heat pump operates on the ideal vapor compression refrigeration cycle with r-134a as the working fluid. the load on

  Two slender rods of negligible weight are pin-connected at

two slender rods of negligible weight are pin-connected at a and attached to the 18-lb block b and the 80-lb block c as

  What is the ratio of the two weights assume that the earth

the earth spins about its own axis at an angular velocity omega. imagine an experiment where an object of mass m kg is

  Find the work done per pound of water during the expansion

water in a piston-cylinder initially starts at t 400of and p 200 psia. the piston is heated until it final volume is

  The thickness of the conductive surface is 0005 m and its

saturated steam condenses completely to liquid water at a rate of m1 2 kgs at 40 bar pressure saturation temperature

  During the expansion some of the water evaporates but no

ten grams of liquid water at 95 c are contained in the insulated container shown. the pin holding the frictionless

  Determine the mass flow rate of liquid water required to

a stream of saturated liquid water at 25u25e6c is added to a 3kgs stream of steam with a pressure of 5 bar and a

  Find the desired radius and mass of the absorber

Find the desired radius and mass of the absorber if the absorber is to not exceed an angular deflection amplitude of 30 degrees when the engine is running at 750 rpm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd