Compute the corresponding change in the volume of the tank

Assignment Help Mechanical Engineering
Reference no: EM131347814

The spherical gas tank is made of steel (E = 29 × 106 psi; v =0:3). The inner radius of the tank is 20 ft and its wall thickness is 1.0 in.

(a) If the working stress of the steel is 9000 psi, determine the maximum safe pressure for the tank.

(b) Compute the corresponding change in the volume of the tank.

Reference no: EM131347814

Questions Cloud

Determine the synthetic formula of the mutants body tissue : Determine the synthetic formula (CnHm) of the mutant's body tissue.- The carbon and hydrogen percentages by mass in the tissue.
Develop an inspection checklist : Your inspection checklist should consist of at least two pages. Retain this checklist because it will be expanded upon in Unit VI and utilized in Unit VII.
Briefly trace the development and growth of the organisation : Briefly trace the development and growth of the organisation from its beginnings to the present through the application of corporate strategies - what types of strategies have these been?
Identify an ethical issue that you encountered in a business : After reviewing these materials, identify an ethical issue that you encountered in a business setting and discuss this in terms of how the scenario impacted you emotionally and how it might be considered from the position of intuitionism.
Compute the corresponding change in the volume of the tank : The spherical gas tank is made of steel (E = 29 × 106 psi; v =0:3). The inner radius of the tank is 20 ft and its wall thickness is 1.0 in.
Determine temperature to which the exhaust must be cooled : Determine the temperature to which the exhaust must be cooled to cause the water vapor to condense, if the exhaust is at a total pressure of 22.223 psia.
Healthcare administrative critical thinking : Assignment length: Develop a minimum of 7 paragraphs. This assignment should be completed in a .doc or .docx file (as a Word document) in APA formatting with a title page
Discuss the potential negative individual : Discuss the potential negative individual and organizational consequences for Asian Americans being perceived as a "model minority."
Calculate the number of ideal stages required for two cases : However, combining the two streams and feeding at one point would be a simpler operation. For the same reflux rate, calculate the number of ideal stages required for the two cases.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the motorist wishes to pass the light without stopping

a motorist is traveling 72km h when she observes that a traffic light 320m ahead of her turns red. the traffic light

  Determine the largest load which can be applied knowing

a block of 10-in length and 1.8 times 1.6 in. cross section is to support a centric compressive load p. the material to

  Determine the normal stress in section bc

The rod ABC is made of steel (E = 29 X 10^6 psi). Determine the normal stress in section BC. Determine the deflection at point B and C.

  Find the power radiated per unit solid angle by the particle

Time average your result in part (b). (Just set up the expression for time average).

  Determine the temperature of the towel

Determine the temperature Ts of the towel. What is the corresponding evaporation rate for a towel that is 0.75 wide by 1.50 m long

  Display the motion of the particle as an animation

The particle is under the influence of gravity. This example was used as an example of a case where spherical or cylindrical coordinates might make the problem easier to solve than Cartesian coordinates. This extra credit assignment will examine t..

  Find the velocity at section three

A 2-D reducing bend (of unit width w) is shown below. Note that flow enters the bend at section 1 with a linear velocity profile, but at sections 2 and 3 is uniform. Find the velocity at section 3.

  Compute the angle that will give a 15 cm oil deflection

the inclined-tube manometer has d 76 mm and d 8 mm and is filled with meriam red oil. compute the angle that will

  Determine the cop of the heat pump

Determine the COP of the heat pump that applies energy to a house at a rate of 4500kj/h for each kW of electric power it draws. Also, determine the rate of the energy absorption from the outdoor air.

  At the exit the pressure is 01 bar the quality is 09 90 and

a steam turbine operates at steady state with a steam mass flow rate of 4600 kgh producing a power output of 1000 kw.

  Determine the value of the vertical load p

The bent circular bar is made of steel with a yield stress of 30 ksi.

  Determine the max shear developed on the web of this beam

a w16 x 50 steel beam supports a uniform load and a concentrated load. the distributed load is 1.5 kipft and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd