Compare the input sequences on the two inputs

Assignment Help Electrical Engineering
Reference no: EM13271321

A sequential circuit hast two inputs (w1 and w2) and one output (z). Its function is to compare the input sequences on the two inputs. If w1 = w2 during any four consecutive clock cycles, the circuit produces a z=1; otherwise, z=0. For example: w1 : 0 1 1 0 1 1 1 0 0 0 1 1 0 w2 : 1 1 1 0 1 0 1 0 0 0 1 1 1 z : 0 0 0 0 1 0 0 0 0 1 1 1 0 Derive the state table.

Reference no: EM13271321

Questions Cloud

Find the velocity of the regulation hockey puck : A regulation hockey puck of mass 675 g is sliding right at 1.66 m/s. What is the velocity (including magnitude and direction left/right) of the regulation hockey puck after the collision
Explain the molar heat capacities for liquid gaseous water : The enthalpy of vaporization of water at 373 K and 1 bar is 40.7 kJ/mol and the molar heat capacities are 75.3 J/(mol K) for liquid and 33.6 J/(mol K) for gaseous water. Find the enthalpy of vaporization of water at 273 K and 1 bar.
What is the power dissipation in inverter at clock frequency : what is the power dissipation in this inverter if the clock frequency is 500MHz. Assume the supply voltage is 3V and the process is characterized by a reference inverter with tREF=20ps, CREF=4fF, RPDREF=2.5K
How fast is she going : A runner approaching the start/finish line hears the bell signaling one lap to go. The bell emits a 352 Hz tone, How fast is she going
Compare the input sequences on the two inputs : A sequential circuit hast two inputs (w1 and w2) and one output (z). Its function is to compare the input sequences on the two inputs. If w1 = w2 during any four consecutive clock cycles, the circuit produces a z=1
Find the velocity of the plane relative to the earth : A plane is headed due west with an air speed of 224 m/s. Find the velocity of the plane relative to the earth
Calculate minimum power required to operate the heat pump : Under steady operating conditions, cold water at 15 oC and 200 kPa enters the water heater with a flow rate of 54 kg/min and leaves the water heater at 80 oC and 200 kPa. During its operation the water heater loses heat to its surroundings at the ..
What is the speed of recoil of the cannon : A 10.1-kg cannonball is fired from a 3,350 kg cannon with a velocity of 198 m/s. What is the speed of recoil of the cannon
What is the total mass of the pluto-charon system : The largest moon of Pluto, Charon, was discovered in 1979. Charon is in a circular orbit of radius 19,600 km around Pluto, What is the total mass of the Pluto-Charon system

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the real and reactive power flowing into at bus p

A transmission line has a resistance of 0.001 pu , and 0.01 p.u reactance. Voltages at the both ends (p and q) of the transmission line are 1.0p.u each. Angle at bus "p" is 45o and the angle at bus " q" is 30o.

  Which type of gates-xor or xnor is simpler to use

If you are asked to build an 8 bit odd parity generator/ checker with the output ERROR=1. when there is a 1 bit error, which type of gates, XOR or XNOR is simpler to use Explain

  What are the expected bond angles in an a-4 molecule

what are the expected bond angles in an AX4 tetrahedral molecule,an AX3 trigonal planar molecule,an AX2 linear molecule,and an AX6 octahedral molecule

  Calculate the maximum doppler shift seen at x-band

An interplanetary spacecraft far beyond Earth's orbit communicates with an equatorial ground station on the Earth. Calculate the maximum Doppler shift seen at X-band (8.4 GHz) due just to the Earth's revolution around the Sun and Earth's rotation ..

  What is the minimum value of t for reliable data sample

A 10-bit unipolar ADC with a reference of 5.00 F and a 44 micro seconds conversion time will be used to collect data on time constant measurement. Thus, the input will be of the form V (t) = 4(1-e^t/T) . What is the minimum value of T

  How many pulses are needed from the controller every second

A 3-Phase stepping motor is to be used to drive a linear axis for a robot. The motor output shaft will be connected to a screw thread with a screw pitch of 5 mm. We want to be able to have a spatial control of at least 0.1 mm.

  Determine whether the statements are valid or invalid

determine whether the statements are valid or invalid. If a statement is valid, please give a proof as in problem 1. If a statement is invalid, you need only provide a counterexample. If x + y = x + z, then y = z

  Find what is the resolution in degrees per state

An absolute optical rotary encoder has five tracks. How many bits is the output, and what is the resolution in degrees per state (that is, degrees per LSB)

  How much charge passes through a cross section

the ends of a length of wire are labeleda and b. If the current in the wire is iab = -3A, are electrons moving toward a or b? How much charge passes through a cross section of the wire in 3 seconds?

  Determine the equivalent impedance of the transformer

determine the equivalent impedance of the transformer referred to the high side (assume the equivalent resistance is negligible). Hint: draw a phasor diagram showing I E V and the impedance drop.

  Express h in standard form for drawing a bode plot

Plot the Bode straight-line approximation phase plot (i.e., f(f) vs. f) for the transfer function over the range f = 10 rad/s to f = 100 krad/s using the 4-cycle semi-log graph paper provided. Label all slopes in degrees/dec and all levels in degr..

  Find the magnitude of the electrical field at a position

A long straight metal wire of radius r1= 2.20E-2 m is surrounded by a metalic cylindrical shell of inner radius r2= 1.24E-1 m and outter radius r3= 1.91E-1 m. The axes of the wire and the cylindrical shell coincide.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd