Compare the equivalent and nominal p-model for the line

Assignment Help Electrical Engineering
Reference no: EM131068545

Question 1-

a) A single phase 132 kV, 50 Hz overhead transmission line is shown in Fig.Q1a. The radius of each sub-conductor is 0.67 cm. Find the equivalent representation of the line and capacitance between the lines (h= 0.0866 m, D=6 m, and d=10 cm).

1222_Figure.png

b) A three phase 500 kV, 50 Hz, 400 km transposed uncompensated line has two Pheasant 1,272,00 cmil 54/3 ACSR conductors per bundle. Each conductor has a diameter of 4.4755 cm, with 50 cm between conductors in the bundle. The horizontal spacings between bundles centres are 10, 10, and 20 m.

Assuming positive-phase sequence, calculate

i. Inductive reactance Ω/km and capacitive reactance F/km of the line (For resistance, from table of characteristic for ACSR, assume a 50°C conductor temperature);

ii. ABCD constants of the line (Assume a 50°C conductor temperature);

iii. Compare the equivalent and nominal π-model for the line;

iv. At the full load the line delivers 800 MW at 0.9 leading power factor and at 480 kV to the receiving end load. Calculate voltage regulation and efficiency of the line.

v. To improve the line performance, identical series capacitors are installed at both ends in each phase of the transmission line, providing 40% compensation. Determine the compensated ABCD constants and maximum power that this compensated line can deliver and compare with the uncompensated one.

Question 2- A three generator power supply system is connected to a bus network operating at a common voltage of 220 kV. The network is shown in Figure Q2a and Q2b.

The neutral of each generator is grounded through a j0.045 p.u. reactor. The generators are not loaded and are running at rated frequency and voltage. The system sequence impedance data on a common base of 220 kV and 100 MVA are given in Table. I.

A double line to ground fault occurs, between the phases detailed in Table. II and ground, at the bus shown in Figure Q2, through a fault impedance of j0.035 p.u.. Assuming the pre-fault bus voltages as 1 p.u., calculate

1. The 10 x 10 admittance matrices for the zero, positive and negative sequence circuits;

ii. Zkk for each of the zero, positive and negative sequence., where k is the number of the bus on which the fault occurs.

iii. The fault current;

iv. The current delivered during the fault by the generator detailed in Table. II; and

v. The current in the line detailed in Table. II during the fault.

338_Figure1.png

TABLE I. System Parameters

Equipment

Voltage (kV)

x° (p.u.)

Xl. (p.u.)

X2 (p.u.

G1

25

0.036

0.072

0.101

G2

25

0.041

0.081

0.113

G3

25

0.038

0.076

0.106

T1

25/220

0.091

0.091

0.091

T2

25/220

0.093

0.09S

0.093

T3

25/220

0.111

0.111

0.111

Line 4-5

220

0.438

0.125

0.125

Line 4-7

220

0.581

0.160

0.166

Line 4-9

220

0.543

0.155

0.155

Line 4-10

220

0.305

0.087

0.087

Line 5-6

220

0.459

0.131

0.131

Line 6-7

220

0.473

0.135

0.135

Line 6-10

220

0.235

0.067

0.067

Line 7-8

220

0.427

0.122

0.122

Line 8-9

220

0.504

0.144

0.144

TAELE II. System Parameters

Fault
phase

Fault
bus

Gen
Current

Inter-bus
Current

Bus
p

Bus
q

Bus
r

Bus
x

Bus
v

Bus
z

c

8

1

6, 10

3

2

1

4

5

6

N.B.: Show full working and submit all code used in Your calculations.

Attachment:- ACSR.rar

Reference no: EM131068545

Questions Cloud

Fundamentals of corporate finance-nominal vs real cash flows : You are graduating in two years. You want to invest your current savings of $5,000 in bonds and use the proceeds to purchase a new car when you graduate and start to work. You can invest the money in either bond A, a two-year bond with a 3% annual in..
Six key dimensions to e-commerce security : Question 1: The six key dimensions to e-commerce security are nonrepudiation, authenticity, availability, integrity, privacy, and:
Capital budgeting in not for profits : Capital Budgeting in Not for Profits Are the capital budgeting criteria discussed in chapter 9 of the Ross text applicable to not for profit corporations? How should such entities make capital budgeting decisions? What about the US Government? Should..
Portfolios of asset and risk-free asset : Using the SML [LO 4] Asset W has an expected return of 13.75 percent and a beta of 1.4. If the risk-free rate is 4.65 percent, complete the following table for portfolios of Asset W and a risk-free asset. (Leave no cells blank - be certain to enter "..
Compare the equivalent and nominal p-model for the line : Compare the equivalent and nominal π-model for the line; At the full load the line delivers 800 MW at 0.9 leading power factor and at 480 kV to the receiving end load. Calculate voltage regulation and efficiency of the line
The primary area of concern identified by management : Geeta & Company has experienced increased production costs. The primary area of concern identified by management is direct labor. The company is considering adopting a standard cost system to help control labor and other costs. Useful historical d..
Determine the unit cost for materials and conversion : Compute the equivalent units for materials and conversion costs. Determine the unit cost for materials and conversion. Compute the predetermined overhead rate for each activity base.
Relationship between datasets and information literacy : 92917 Using Health Care Data for Decision Making Examine the relationship between datasets and information literacy and explain the data elements in contemporary health data terminologies;
Calculated using the average daily balance : Please explain in detail. Thank you! We assume that the billing period is one week rather than one month and that the weekly rate is 1%. You begin with a balance of $1000.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find voltage regulation for load at leading power factor

A 3 phase Y connected alternator is rated at 1600 KVA, 13500 V. The armature resistance and synchronous reactance are 1.5 ohms and 30 ohms respectively. Calculate the % voltage regulation for a load of 1280 KW at 0.8 leading power factor.

  Design butterworth digital filter with linear transformation

The specification of the desired low pass filter are A min=23 dB, A max=5dB, P=02 and S=0.6. Design a Butterworth digital filter using bilinear transformation.

  What would be the degree and the values of coefficients

Inverse Z-transform and poles and zeros. When finding the inverse Z-transform of functions with z-1 terms in the numerator, the fact that z-1 can be thought of as a delay operator can be used to simplify the computation.

  What would be the minimum vars rating of the inductor

you have the task of ordering a replacement inductor for one that has become defective. The information on the nameplate has been painted over and cannnot be read. The machine that contains the inductor on 480V at a frequency of 60 Hz.

  Calculate the current that flows in the remaining two

Three 5 ohm resistors are connected in wye across a 3-phase,480V line. Calculate the current flowing in each. If one of the resistors is disconnected, calculate the current that flows in the remaining two.

  What is the value of the total circuit complex impedence

An input signal of 10V at 0 degrees is applied to a series RLC circuit with resistore R=100 ohm, inductor L=40 mH, and capacitor C = 0.5uF. determine what is The value of the total circuit complex impedence.

  Design combinational logic circuit that compare 2- bit num

Design a combinational logic circuit that compare two 2- bit number. The circuit must have three outputs indicationg if the two numbers are equal, first larger than the second, or the second is larger than the first.

  Compute the covariance function and the variance

A certain signal is modeled by a continuous Gaussian random process X(t) with mean E {X(i)} = 2 and autocorrelation function R(t, r) = 4 + e-0.5|r|. Compute the covariance function C(t, r). Compute the variance of X(t). Write the PDF for a single ..

  Determine the inductance of the second coil

A 100-turn coil is wound on a toroidal core and has an inductance of 100 mH. Suppose that a 200-turn coil is wound on a second toroidal core having dimensions (r and R as shown in Figure) that are double those of the first core. Both cores are mad..

  Design the details of the d-a using a weighted resistor

design the details of the D/A using a Weighted Resistor( NOT R-2R) technique, as well as the logic details of the sequencer/decision maker/state machine which sequences the A/D through its conversion steps to convert an analog input into a 4-bit b..

  How the voice message is best received

You have a shortwave AM receiver (just an AM receiver that has the capability to receive signals in the FM frequency band) that receives an NBFM voice signal at some carrier frequency. You notice, however, that while the signal strength is maximiz..

  Determine what type of driving style is being used

.a. If the following voltage pulse is being applied to a stepper motor coil to the increment the shaft, what type of driving style is being used b. What advantage does this have as opposed to a constant-voltage pulase

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd