User Account

All Pages

Compare air and helium as cooling media for electronic

Assignment Help Mechanical Engineering
Reference no: EM13612795

Compare air and helium as cooling media for electronic devices. Both fluids must exit through an area of 0.025 m^2. The exit temp is limited to 60 c the inlet temp can be as low as 10 c and as high as 25 c . Heat is released at a rate of 1 kW. The inlet area is so large that the inlet velocity is negligible. Treat both helium ans air as ideal gasses.

Reference no: EM13612795

Questions Cloud

A 300g ball is tied to a string it is pulled to an angle of : a 300g ball is tied to a string. it is pulled to an angle of 4.00 degrees and released to swing as a pendulum. a
X is 50 years old unmarried without children and has : x is 50 years old unmarried without children and has earnings during 2011 of 8000. he is not claimed as a dependent on
A person with a mass of 50 kg is standing on a scale in an : a person with a mass of 50 kg is standing on a scale in an elevator that is accelerating upwards at a rate of 3.2 ms2.
Tangshan china company balance sheet shows total assets of : tangshan china company balance sheet shows total assets of 60 million total liabilities including preferred stock of 45
Compare air and helium as cooling media for electronic : compare air and helium as cooling media for electronic devices. both fluids must exit through an area of 0.025 m2. the
A building is being knocked down with a wrecking ball which : a building is being knocked down with a wrecking ball which is a big metal sphere that swings on a 13-m-long cable. you
If the volume of the air in the tank is 2 cubic meters find : an insulated rigid-wall tank contains air at 20 c and 2 bar. a paddle wheel located in the tank does work on the air in
Three capacitors 40 60 and 80 microf are connected in : three capacitors 4.0 6.0 and 8.0 microf are connected in series across a 50.0 v battery. find the voltage across the
In our online lecture we include a quote by e o wilson the : in our online lecture we include a quote by e. o. wilson the one process now going on that will take millions of years

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the rate of heat loss from the molten salt

Determine the rate of heat loss from the molten salt per meter length of the pipe.

  Determine the number of revolutions

Determine the number of revolutions that the motor executes in a) reaching its rated speed, b) coasting to rest.

  A charged particle with a charge-to-mass ratio of qm 57

a charged particle with a charge-to-mass ratio of qm 5.7 108 ckg travels on a circular path that is perpendicular to a

  The valve is next opened and steam from the line at 135 mpa

a tank has a volume of 0.35m3 and initially contains saturated vapor at 333 kpa. the valve is next opened and steam

  The given figure depicts an indirectly fired gas turbine

the given figure depicts an indirectly fired gas turbine engine. in the gas turbine engine air is compressed to a high

  A stack gas flowing at 80 m3min at t 25 degree c and 1 atm

a stack gas flowing at 80 m3min at t 25 degree c and 1 atm contains approximately 75 n2 5 o2 8 h2o and 12 co2. a

  Determine the angular velocity

At a given instant in time, flywheel OA is caused to rotate with angular velocity of w=2rad/sec and angular acceleration of alpha=6rad/s2. determine the angular velocity of links AB and BC at this instant in time. AB=.5m, BC=.4m, OA=.3m

  Determine the reactions of simply supported

Determine the reactions of simply supported beam to both a concentrated and uniform load. A beam with a span of 21 ft is simply supported at the left-hand end and fixed at the right-hand end.

  A bullet of mass 006 kg is fired horizontally into a wooden

a bullet of mass 0.06 kg is fired horizontally into a wooden block of mass 0.10 kg. the wooden block is suspended from

  One pound mass of water in a piston-cylinder assembly

one pound mass of water in a piston-cylinder assembly initially a saturated liquid at 1 atm undergoes a

  Calculate the break hp of the pump using water

Using a centrifugal pump, and a flow rate of 60 gal/min, calculate the break hp of the pump using water with a density of 62.4lbm/ft3 and do the same for a nonviscous liquid having a density of 0.85g/cm3.

  Two tanks are connected by a valve and line as shown below

two tanks are connected by a valve and line as shown below. the volumes are both 1 m3. tank anbspcontains r-134a at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd