Cnsider the posts in their initial unyielded state if p

Assignment Help Mechanical Engineering
Reference no: EM13634249

The rigid beam shown is supported by three cylindrical posts which rest on a rigid base: a 20 mm dia. brass post at B

(E =100 GPa and syld = 600 MPa) and two 75 mm dia. aluminum posts at A and C (E=70 GPa and syld = 20 MPa). All three posts are initially of equal length and free of residual plastic strain.

a. Sketch to scale, on the same graph, axial compressive stress-strain curves for both post types. Extend the curves out to the point where both post types have yielded.

b. If the beam is loaded until, for each load, P = 100 kN and then unloaded to P = 0 kN, on which post or posts will the beam finally rest?

c. After this load cycle, what will be the residual plastic strain (if any) be in each post?

d. What load P would be required to cause all three posts reach their yield point?

e. Consider the posts in their initial unyielded state. If P = 50kN, for what temperature change T would the gap between the brass post and rigid beam equal 10mm?

Reference no: EM13634249

Questions Cloud

A gasmixture contains 128 g n2 and 085 g o2 in a155 l : 1. calculate the root square mean velocity of cl2 at 25 ordmc.2. an unknowngas effuses at a rate that is 0.462 times
Gve the state temperature pressure quality if applicable : design a rankin cycle to analyze. the only restrictions are that water must enter the turbine as a superheated vapor
The kid twirls it just fast enough to keep it moving in a : a kid plays with a yo-yo of mass 125 g and twirls it in a vertical circle. the lneght of the string is 90.0 cm. the kid
For the funtion fx6x2 make a table of slopes of secant : for the funtion fx6x2 make a table of slopes of secant lines and make a conjecture about the slope of the tangent line
Cnsider the posts in their initial unyielded state if p : the rigid beam shown is supported by three cylindrical posts which rest on a rigid base a 20 mm dia. brass post at be
On december 1 1783 jacques charles became the first human : on december 1 1783 jacques charles became the first human topilot a non-tethered hydrogen balloon. he flew the balloon
As the contents of the container come into thermal : a sealed evacuated 1.11 liter container initially contains 0.32 liter of liquid helium. as the contents of the
The mean per capita income is 17635 dollars per annum with : the mean per capita income is 17635 dollars per annum with a standard deviation of 891. what is the probability that
A what is the net electric force on the flea b one of the : a bicycle wheel with radius 35 cm has 73 charges 1.0 microc each spaced at regular intervals along its edge. a flea

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd