Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Capture the following system behavior as an HLSM. The system counts the number of events on a single bit input B and always outputs that number unsigned on a 16-bit output C, which is initially0. An event is a change from 0 to 1 or from 1 to 0. Assume the system count rolls over when the maximum value of C is reached.
A magnetic dipole mux of infinitesimal radius is located at (1, 0, 0). The magnitude of B at the origin (0, 0, 0) is 2.5 T. Find B in vector form at (3, 0, 0).
A linear circuit has a capacitance of 1.0 mF and an inductor of 1.0 µH. If the frequency response of the voltage gain should stay the same and the capacitor is scaled to 70 µF, what should the value of the inductor be
Moore sequential circuit, A Moore sequential circuit has one input and one output.The output goes to 1 when the input sequence 111 has occurred and the output goes to 0 if the input sequence
Find the current that flows in a silicon bar of 10-µm length having a 5-µm x 4-µm cross section and having free electron and hole densities of 105 / cm³ and 1015 / cm³, respectively, when a 1 V is applied end-to-end. Use µn = 1200 cm²/V·s and µp =..
A machinable grade of aluminum is to be milled on an NC machine with a 20 mm diameter four tooth end miling cutter, Cutting speed = 120 m/min and feed = 0.008 mm/tooth. Convert these values to rev/min and mm/rev.
A helical spring is fabricated by wrapping wire ¾ in. in diameter around a forming cylinder 8 in. in diameter. Compute the number of turns required to permit an elongation of 4 in. without exceeding a shearing stress of 18 ksi. G = 12 × 106 psi.
A 4 ohms resistance is in series with the parallel combination of a 20 ohms resistance and an unknown resistance R sub x. The equivalent resistance for the network is 8 ohms. Determine the value of R sub x.
Suppose a signal is sampled at 1 kHz and you compute the DFT of the signal using 1000 signal samples. What frequency in Hz corresponds to the 150th value of the DFT
A series RC circuit is powered by a voltage supply of 120Vac and60Hz. The resistor has a resistance of 80W and capacitive reactanceis 60W. (1) Sketch a schematic for this circuit (2) Determine the capacitance of the capacitor
Consider the analogue cosine signal y(t) = COS(8.8pit). It is sampled using a sampling interval of T = 0.5 sec. What is meant by the term aliasing in regard to signal sampling What is the minimum sample rate that should be used to avoid aliasing
given a "black box" with two terminals. You play around with the box for awhileand make the following observations: (i) The output voltage from the box is sinusoidal. (ii) The peak magnitude of the open-circuit voltage at the terminals is 5 V.
A 12-bit ADC with a Vref of 5V is used to digitize small signals with a quiescent value of 2.5V and a variation around 2.5 of +/- 100mV. What is the SNR of the digitized signal if the ADC is ideal
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd