Calculating the velocity gradient across the 80 cm height

Assignment Help Mechanical Engineering
Reference no: EM13641397

Blood flows up a vein with a uniform radial velocity and radius of 5 Doppler ultrasound tells you that the velocity between 3 points space apart are 0.64,0.6, and 0.52 mm/s moving up the vein, repectively. Assuming blood's density of 1025 kg/m3 at the middle point, determination blood's density gradient at the niddle measurement location calculating the velocity gradient across the 80 cm height of the vessel. Solve the problem using cyclindrical coordinates but you do not need to use the full Navier-Stakes equation.

Reference no: EM13641397

Questions Cloud

A popular entertainment at some carnivals is the blanket : a popular entertainment at some carnivals is the blanket toss.a if a person is thrown to a maximum height of 28.0ft
The rate of flow of steam is 05 kgs calculate the quality : steam enters the nozzle of a turbine with a low velocity at 3 mpa 350degc and leaves the nozzle at 1.6 mpa at a
A peice of iron mass250 g at 398 k is placed in a styrofoam : a peice of iron mass25.0 g at 398 k is placed in a styrofoam coffee cup containing 25.0 ml of water at 298 k. assuming
A 1600 kg car is traveling along a straight road at 20 ms : a 1600 kg car is traveling along a straight road at 20 ms. two seconds later its speed is 21 ms. what is the magnitude
Calculating the velocity gradient across the 80 cm height : blood flows up a vein with a uniform radial velocity and radius of 5 doppler ultrasound tells you that the velocity
The reaction of 0779 g k with oltsubgt2ltsubgt forms 1417 : the reaction of 0.779 g k with oltsubgt2ltsubgt forms 1.417 g potassium superoxide a substance used in self-contained
Calculate the standard deviation for random variable : calculate the standard deviation for random variable
A block with a mass m and charge q is placed in an electric : a block with a mass m and charge q is placed in an electric field e a i b j where a and b are constants. if the block
You are choosing among three investment plans the payoffs : you are choosing among three investment plans. the payoffs of these investment plans depends on next years gdp see the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the acceleration of the mass center of the disk

a 4-in. diameter disk shown weighs 10 lb. the disk is released at rest when theta30 degrees and rolls down the curved

  What is the nominal shear stress at the surface bif a

a 2in-diameter steel propeller shaft of an experimental high-speed boat transmits 2500hp at 2000rpm. bending and axial

  A 03 kg bullet is fired into a 36 kg wooden block and

a 0.3 kg bullet is fired into a 3.6 kg wooden block and becomes embedded in it. knowing that the block and bullet move

  What is differential levelling list the procedure for

what is differential levelling? list the procedure for carrying out a differential levelling exercise where one point

  1 kg of air is allowed to expand reversibly in a cylinder

1 kg of air is allowed to expand reversibly in a cylinder behind a piston in such a way that the temperature remains

  The thermal conductivity of the solid is 190 wm-k and its

a solid cylinder 100 mm in diameter generates heat at a uniform rate of 7 x 106 wm3. the thermal conductivity of the

  A 25 mm diameter uniform steel shaft is 600 mm long between

a 25 mm diameter uniform steel shaft is 600 mm long between bearings.a find the lowest critical speed of the shaftb if

  Design a 1d compressed air rocket engine assume standard

design a 1d compressed air rocket engine. assume standard atm conditions and isentropic flow. k1.4 r0.287determine1.

  Are there alternative solutions which might also effective

how can this goal be achieved? are there alternative solutions which might also be effective?

  Calculate the power required to drive the plant

A refrigerating plant operating between temprature limit of 253k and 307k provides 4.5kJ/s of refrigerating effect. If the refrigerating efficiency of the plant is 0.76. calculate the power required to drive the plant.

  Determine the steady state surface

A thin electric heater is wrapped around a rod of diameter 3 cm. The heater dissipates energy uniformly at a rate of 1300 W/m. Air at 20°C flows normal to the rod with a velocity of 15.6 m/s. Determine the steady state surface temperature of the h..

  Calculate the steady rate of entropy production samp kjks

draw a complete schematic diagram show arrows symbols amp numeric values for each w amp amp q amp . consider the steady

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd