Calculating the convective part of the heat transfer

Assignment Help Mechanical Engineering
Reference no: EM131147858

A 0.25 mm diameter platinum wire, 0.2 m long, is to be held horizontally at 1035?C. It is black. How much electric power is needed? Is it legitimate to treat it as a constant-wall-temperature heater in calculating the convective part of the heat transfer? The surroundings are at 20?C and the surrounding room is virtually black

Reference no: EM131147858

Questions Cloud

What are the advantages and disadvantages of social media : What are the advantages and disadvantages of easily obtainable information? What are the advantages and disadvantages of social media? How might knowing these advantages and disadvantages alter how a person might use social media?
Determine notable health indicators for your adopted country : Determine notable health indicators for your adopted country: life expectancy, infant mortality, and one more that is relevant for your country
How many people would have to attend gala for organization : If Meals charged $275 per ticket, how many people would have to attend the gala for organization to break even on the event? If Meals charged $300 per ticket, the contribution margin from each ticket sold would be: _____.
How much power can it dissipate : How much power can it dissipate if it melts at 1200?C? Note all assumptions and corrections. Include radiation using Frod-room = 0.064.
Calculating the convective part of the heat transfer : How much electric power is needed? Is it legitimate to treat it as a constant-wall-temperature heater in calculating the convective part of the heat transfer? The surroundings are at 20?C and the surrounding room is virtually black
What horsepower pump is needed : Water at 20°C is to be pumped through 2000 ft of pipe from reservoir 1 to 2 at a rate of 3 ft3 /s, as shown in Fig. P6.62. If the pipe is cast iron of diameter 6 in and the pump is 75 percent efficient, what horsepower pump is needed?
Estimate the steady heat flux and the rate of condensation : Estimate the steady heat flux and the rate of condensation - When the plate is perfectly horizontal and filled to over- flowing with condensate.
Describing using three different social media platforms : Write a 350- to 700-word summary describing using three different social media platforms with the objective of networking within your career field. Use your current social media accounts, or create new ones. Incorporate research regarding how to ..
Determine which candidate would be the right fit : Determine which candidate would be the "right fit". Support your decision by describing the thought process that lead up to your decision

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What are the temperature and pressure at the nozzle exit

Room temperature atmospheric air is accelerated by a nozzle steadily from a low velocity to a velocity of 220 m/s. If the nozzle diameter decreases by a factor of 2:

  A stone of mass m is tied to one end of a string ans is

a stone of mass m is tied to one end of a string ans is rotated with constant angular vel. w. the length of the string

  Construct the truth table to evaluate the effect of each

the pump motor control relay is controlled by the following sensorsa position sensor to sense if the train car is in

  A rubble masonry open chanel is being designed to carry

a rubble masonry open chanel is being designed to carry 500 ft 3 s 14 m 3 s of water on a 0.0001 slope. using n 0.017

  An air conditioner uses r134 the condenser pressure is 1400

an air conditioner uses r134 the condenser pressure is 1400 kpa and the evaporator pressure is 201 kpa. find the cycle

  The temperature is 68 f and the velocity is 40 fts the exit

a pump steadily draws water at a mass flow rate of 20 lbms through a piping arrangement. the pressure at the inlet is

  Determine the acceleration of the mass center of the disk

a 4-in. diameter disk shown weigts 20 lb. the disk is released at rest when theta30 degrees and rolls down the curved

  Resultant of the parallel coplaner force system

Determine the resultant of the parallel coplaner force system shown in fig

  Determine the magnitudes of r

The combined action of the three forces on the base at O may be obtained by establishing their resultant through O. Determine the magnitudes of R and the accompanying couple M.

  What is the speed of shaft b

Suppose that the motor is spinning shaft A at a speed of 1800 rpm. State all speeds in units of rpm. What is the speed of shaft B. What is the speed of shall C. What is the speed of shaft D?

  Determine the torque exerted on the 10mm long high inner

whole blood is placed in a concentric cylindern viscometer. the gap width is 1 mm and the inner cylinder radius is 30

  The corresponding mass flow rates not the original

incoming air flow of 200 m3h at a temperature of 20oc and a humidity ratio of 0.012 kgvkga is mixed in a chamber with

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd