Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A series circuit has the following components. For each, calculate the voltage across it and the current through it. Component voltage Current 9 V source 9V 9.1 Kohm resistor 1 Kohm resistor 2.2 kohm resistor.
The length of GaAs laser resonator is L = 165 um; the width and the thickness are W = 10 um and d = 0.1 um. Find the photon round-trip time in this resonator. The refractive index of GaAs is 3.7.
make a RAM memory using a 2-D array of integers. This RAM will have 8 locations, each 64 bits wide. Both should be changeable and controlled by generics. This memory will be connected to a FIFO controller which I have already coded.
A process has the dynamics G(s)=5/s^2. Design a unity negative feedback controller of the form G.c(s)=Ks+1 for a step response exhibiting approximately 15% overshoot.
(a) Find the maxterm expression for F. Express your answer both in decimal and algebraic form. (b) Use a Karnaugh map to find the minimum sum-of-products form for F'. (c) Find the minimum product-of-sums for F.
Two rectangular waveguides, one air filled with internal dimensions 2cm x 1cm and the other dielectric filled with internal dimensions 1cm x 0.5cm, have the same cut-off frequency for the dominant mode. what is The relative permittivity of the die..
Design a digital security system for a four-door sedan car. There are sensors on all doors, hood, gas cover, and the trunk. When the car is locked, an alarm will sound if somebody tries to force open the door, hood, gas cover, the trunk, or tries ..
Built-in voltage for a Si p-n junction is tested to be 0.6 V, NA = 2 X 10^15 cm^-3 on p side. Find ND on n side. (Assume ni = 1 x 10^10 cm^-3; and k*T/q= 0.026 V)
An input signal given by Vin(t)=5cos(500pi*t)+5cos(1000pi*t)+5cos(2000pi*t) is applied to a basic lowpass RC filter. R=318.3 ohms and C=1 microFarad. Find the expression for the output signal in terms of t and pi.
A PWM is to be programmed to output a signal with a pulse high width of 150 usec and a pulse low width of 250 usec. What are the values required for prescale (if any) PWMPER and PWMDTY An 8-bit configuration is used and the E-clock is 24 MHz.
V1(18V) R1(1k) R2 (1.5k) R3 (2k)How does the ratio V2 V1 compare to the raioR2 R1?How does the ratio V3 V1 compare to the raioR3 R1 Add the measured voltage V1 V2 and V3 How does this value compare to the value Vt
What are the exact form of the equations for the 2nd-order step response for the underdamped, critically-damped, and overdamped conditions.
An AC Voltmeter uses a bridge rectifier and 100 ohm PMMC which requires a 1mA DC current for full-scale deflection. Assuming ideal diodes, calculate the value of the multiplier resistor to obtain full scale deflection with 10 V AC applied to the i..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd