Calculate the velocity v2 imparted to barge 2 just after

Assignment Help Mechanical Engineering
Reference no: EM13610379

Two barges, each with a displacement (mass) of 550 Mg, are loosely moored in calm water. A stunt driver starts his 1650-kg car from rest at A, drives along the deck, and leaves the end of the 15° ramp at a speed of 62 km/h relative to the barge and ramp. The driver successfully jumps the gap and brings his car to rest relative to barge 2 at B. Calculate the velocity v2 imparted to barge 2 just after the car has come to rest on the barge. Neglect the resistance of the water to motion at the low velocities involved.

Reference no: EM13610379

Questions Cloud

What is the capacitance of the capacitor made this way if : a capacitor is made by taking two sheets of aluminum foil each 0.022 mm thick and placing between them a sheet of paper
Two point charges are on the y-axis a 25 microc charge is : two point charges are on the y-axis. a 2.5 microc charge is located at y 1.50 cm and a -2.48 microc charge is located
Assume the brake pads are 1 lbmin with a heat capacity of : a car with mass 3250 lbm is driven at 60 mih when the brakes are applied to quickly decrease its speed to 20 mih.
A proton is released from rest in a uniform electric field : a proton is released from rest in a uniform electric field of magnitude 373 nc. a find the electric force on the
Calculate the velocity v2 imparted to barge 2 just after : two barges each with a displacement mass of 550 mg are loosely moored in calm water. a stunt driver starts his 1650-kg
Select the appropriate gain to minimize the quantization : a 12-bit ad converter has an input range of plusmn 10 v and is connected to an input amplifier with a programmable gain
Find the force exerted by these charges on a fourth charge : three charges each of magnitude 5.0 nc are at separate corners of a square of edge length 3.0 cm. the two charges at
Consider again the study of the association between : consider again the study of the association between depression and cardiac disease survivability which showed that of
A what is the magnitude of the force that each sphere : two tiny conducting spheres are identical and carry charges of -18.2 microc and 53.0 microc. they are separated by a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The steam is compressed at constant pressure until its

a cylinder contains 2 kg of steam at 200 kpa and 200 c. the steam is compressed at constant pressure until its

  Calculate the total supply flow rate in m3s bthe ratio of

an air conditioning system is designed for a zone with a high dehumidification demands and humid outdoor conditions.

  Observing plastic deformationthe aim of this demonstration

observing plastic deformationthe aim of this demonstration is to make some observations of the surface relief produced

  Air at 01 kgs is to be cooled from 140 c to 40 c in a heat

air at 0.1 kgs is to be cooled from 140 c to 40 c in a heat exchanger. the coolant water is at 20c constant throughout

  What restrictions in the problem are limiting the profit

Solve this problem with a linear programming model. Describe the optimum mix of raw materials and production levels for the products. How much profit does the business make?

  If it is thrown downward released it at 3 ft above the

when a ball is released from rest at a height of 5 ft above the floor it bounces to a height of 3.5 ft. if it is thrown

  Calculate the mean velocity of the water

A new cast iron pipe is 5 km long and 15 mm diameter is used to convey water at a rate of 0.0150m3s-1. Given the absolute roughness of the pipe is 0.26 mm, density of water is 998 kg/m3 and dynamic viscosity of water is 1.14 × 10-3 kgm 1s-1.

  An industrial water shutoff valve is designed to operate

an industrial water shutoff valve is designed to operate with 30lbs of force and will encounter 200lbs of resistance

  Estimate the schmid factor

Estimate the Schmid Factor, which is used to convert the CRSS into a critical tensile 'yield' stress. Use the measured angle between the slip trace and the sample long axis

  Determine the velocity of ship in sea water

determine the velocity of ship in sea water and also the resistance in sea water if density of air 1.3 kg/m and kinematic viscosity of sea water and air as 0.012 and 0.018 stokes respectively.

  Determine the force in members cj of the truss

Determine the force in members CJ of the truss

  How dislocations are involved in each of the strengthening

Describe on your own words the three strengthen mechanism for metals (i.e. grain size reduction, solid solution strengthening and strain hardening). Be sure to explain how dislocations are involved in each of the strengthening techniques.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd