Calculate the uncertainty in the measurement in this length

Assignment Help Mechanical Engineering
Reference no: EM131173669

A small cantilever vibrometer is available for measurement of vibration frequency, but the specification sheet is lost, so that the properties of the device are not known. The instrument is calibrated by placing it on a large compressor in the laboratory which is rotating at 300 ± 2.0 rpm. The measured length for resonance conditions is 5.6 cm ± 0.2 mm. Calculate the frequency that the instrument will indicate when L = 10 cm ± 0.5 mm. Also, calculate the uncertainty in the measurement in this length.

Reference no: EM131173669

Questions Cloud

Suburban town are allergic to ragweed : It has been found that 10% of the people in a suburban town are allergic to ragweed.If 5 people of the town are selected at random, what is the probability that
Review the audit report issued by the external auditing firm : Review the audit report issued by the external auditing firm from the company's Website for year it was accused of fraud. Then, determine whether the external auditors were negligent in preparing the audit report for the company.
Confidence interval on the estimated sample mean : a) Calculate the 90% confidence interval on the estimated sample mean. b) Calculate the 99% confidence interval. Why is this interval larger? c) Explain why this confidence interval would shrink if your sample size was 100 (there  are two reasons).
Determine the expected life of this segment of shaft : The internal diameter of the pressure vessel is 300 mm and the pressure in the vessel varies from 0 to P kPa gauge. Assuming that the bolts are initially tightened to 80% of their yield strength determine the maximum value of P that would not caus..
Calculate the uncertainty in the measurement in this length : Calculate the frequency that the instrument will indicate when L = 10 cm ± 0.5 mm. Also, calculate the uncertainty in the measurement in this length.
Accumulated depreciation should be recorded at : In the financial records of the partnership,  - this equipment and its accumulated depreciation should be recorded at--
Was there a control or comparison group : 1. Is this an experiment or an observational study? Justify your answer. 2. Was there a control or comparison group in this study? If so, describe how this is implemented. If not, briefly discuss a potential problem due to lack of a control or com..
Median of set of integers : If x is the average (arithmetic mean) of 5 consecutive odd integers, what is the median of this set of integers?
Identify activity in doctors office that fall into move time : Identify the activities in the doctor's office that fall into process time, inspection time, move time, wait time, and storage time.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd