User Account

All Pages

Calculate the total complex power

Assignment Help Electrical Engineering
Reference no: EM13161898

Q1. Let us consider a three-phase, balanced, Y-connected source with Vab=400 30∠V rms and 50 Hz. This source supplies the following three loads (i.e. Load-1, Load-2 and Load-3). For this source, calculate the total complex power, total current drawn and the total power factor.

Load-1: three-phase, balanced, Y-connected load with an impedance of (1+ j 6) ohm per phase,

Load-2: three-phase, balanced, Y-connected load with a total three-phase power consumption of 4 kVA at 0.7 PF lagging,

Load-3: three-phase, balanced, Y-connected load with a current consumption of 10 ∠-25o A rms in phase-a,

Q2. For the two-port network given below, calculate the Z, Y, H and T matrices.

Note: First KVLs and KCLs should be written. Then using the main equations on how the Z, Y, H and T matrices are defined, their parameters should be calculated from the KVLs and KCLs.

621_Calculate the total complex power.png

Reference no: EM13161898

Questions Cloud

What is the final temperature of gold : Suppose that 25.0g of gold is initially at 27.0 Celsius. What is the final temperature of gold upon absorbing 2.35kJ of heat?
How many grams of conjugate base do you need : If you wanted to prepare a 1.45 L buffer with a total phosphate concentration of 0.0500 M, how many grams of NaH2PO4 and Na2HPO4 would you mix together? How many grams of conjugate acid do you need? How many grams of conjugate base do you need?
State the equilibrium molar concentration : Calculate the following to determine Kc for FeSCN2+. a,) moles Fe3+ initially present. b.) moles SCN- initially present
What volume of gas will be collected for complete reaction : If O2 is collected over water at 40.0 Celsius and a total pressure of 737 mmHg, what volume of gas will be collected for the complete reaction of 23.92 g of NiO?
Calculate the total complex power : Calculate the total complex power, total current drawn and the total power factor and Y-connected load with an impedance of (1+ j 6) ohm per phase,
How many calories are required to raise the temperature : how many calories are required to raise the temperature of a 150.g sample of gold from 25 Degrees C to 175 Degrees C
State convert the pka values to ka values : Estimate the pH, and the concentrations of all species in a 0.300 M phosphoric acid solution. pKa1: 2.16 pKa2: 7.21 pKa3: 12.32 Hint: Convert the pKa values to Ka values
What is the purpose of the anhydrous cacl2 : what is the purpose of the anhydrous cacl2? the important that none of the solid cacl2 be included in the final distillation of 1-bromobutane.
What is the final temperature : Imagine that you have two iron blocks, one with a mass 226 g at a temperature of 46.0 oC, and another with a mass 380 g at a temperature of 134 oC. The two blocks are brought into contact with each other in an insulated container. What is the fina..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Combinational logic devices for specific purposes

Interpret manufacturer's data sheet to select appropriate combinational logic devices for specific purposes

  Define dynamic ram that must be given a refresh cycle

Dynamic RAM that must be given a refresh cycle 64 times per ms. Each refresh operation requires 150 ns. memory cycle requires 250 ns.

  Explain saturated and unsaturated synchronous reactance

Saturated and unsaturated synchronous reactance, The following readings are taken from the results of an open- and a short-circuit test on a 9375-kVA three-phase Y-connected

  Define a sinusoidal voltage has a maximum value

A sinusoidal voltage has a maximum value of 100V, and the value is 10V at t=0. The period is T=1ms. Determine v(t)

  Computation the percentage second harmonic distortion

Calculate the percentage second harmonic distortion present in the output. Calculate the percentage error in the output voltage compared to its ideal value at the instant of time when t= 1/3200 seconds.

  Comparing error probabilities with bpsk and qpsk systems

Comparing Error probabilities with BPSK and QPSK systems, A BPSK system and a QPSK system are designed to transmit at equal rates; that is, two bits are transmitted with the BPSK system

  Explain telephone channels and pcm analysis

Telephone channels and PCM analysis, The analog to digital converter (ADC) used in a telephone system outputs 8 bit words. The digital words are transmitted as a serial stream to form a PCM voice signal

  Explain combinational versus sequential circuits

(Combinational versus Sequential Circuits) Which of the fol¬lowing contain circuits that are likely to be combinational and which contain sequential circuits? Explain your rationale.

  Explain ac circit analysis and max power transfer

AC Circit analysis and max power transfer, If the output impedance of a certain driving circuit is 50 Ohm - j10 Ohm, what value of load impedance will result in the maximum power to the load?

  Define what is the fm improvement in db

What is the peak frequency deviation of the FM signal? What is the FM improvement in dB?

  What is the maximum symbol rate which can be sent over link

What is the maximum symbol rate which can be sent over this link? If a binary line code is used, what is the maximum bit rate? What is the maximum bit rate with 4-ASK symbols?

  Define dispense requested amount using least number of bills

Dispense requested amount using least number of bills, Write a C program for an automatic teller machine that dispenses money. The user should enter the amount desired (a multiple of 10 dollars)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd