Calculate the time taken to complete first 200 revolution

Assignment Help Mechanical Engineering
Reference no: EM131131874

The speed of an electric motor is increased uniformly from 1200 to 1350 rpm in a time of 1.5 s. Find

(a) the angular acceleration,

(b) the number of revolutions turned during this time.

A winding drum is accelerated from 480 to 840 rpm in a time of 2 s. Acceleration continues at the same rate for a further 4 s after which the drum continues rotating at a steady speed. Calculate the time taken to complete the first 200 revolutions.

Reference no: EM131131874

Questions Cloud

Assume the partnership income sharing agreement : Assume the partnership income-sharing agreement calls for income to be divided 45% to Guillen and 55% to Williams. Prepare the journal entry to record the allocation of net income.
Write a paper about building an it strategic plan : Write a paper about Building an IT Strategic Plan. the paper shall cover any number of topics and areas that we discussed in the course.
What are the five steps involved in the capital budgeting : What are the five steps involved in the capital budgeting process?
What are the key motives for making capital expenditures : What are the key motives for making capital expenditures? Discuss, compare, and contrast them.
Calculate the time taken to complete first 200 revolution : Calculate the time taken to complete the first 200 revolutions.
Do all capital expenditures involve fixed assets : What is capital budgeting? Do all capital expenditures involve fixed assets? Explains
What are the prosecutor ethical dilemmas or esponsibilities : The judge that you were scheduled to try your case before was recently re-elected thanks to large campaign contributions from influential supporters. Can this judge be objective?
Prepare a schedule showing the distribution of net income : F. Calvert and G. Powers have capital balances on January 1 of $50,000 and $40,000, respectively. The partnership income-sharing agreement provides for
Calculate the new required return : The Parker Company's stock has a beta of 1.2. The risk-free rate is presently 5 percent and the market risk premium is 4%. Calculate the new required return if the slope of the SML is now 0.05

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine an appropriate summertime indoor design

determine an appropriate summertime indoor design temperature for an exercise area located within an office complex.

  Assuming constant specific heats at 400 k determine the

a piston-cylinder device has nitrogen gas at 160 kpa and 158oc. the 23-cm diameter piston initially pushes against a

  A flue passing hot exhaust gases has a square cross section

a flue passing hot exhaust gases has a square cross section 300mm to a side. the walls are constructed of refractory

  Determine the radius of curvature of the trajectory and the

a ball is released with the initial velocity of 80 ftsec at an angle of 35 degrees. determine the radius of curvature

  A 7-m- diameter spherical hot air ballon is neither rising

a 7-m- diameter spherical hot air ballon is neither rising nor falling at some height. the density of atmoshpheric air

  Device creates or destroys energy or destroys entropy

The Acme Company claims to have designed an adiabatic turbine that will produce 126.2 BTU per pound of steam. The operating conditions are labeled on the diagram below. Is this company's claim valid or is this a perpetual motion machine? Hint: Determ..

  Magnitude of average external torque

During the launch ,what is the magnitude of average external torque on her fromthe board?

  Creating a grid and specifying the intial flow velocity

Need to get flow around cylinders in a channel by creating a grid and specifying the intial flow velocity.

  Accounting for the variation of specific heatsaccording to

a simple ideal brayton cycle with air as the working fluid has a pressure ratio of 11. the air then enters the

  Determine the total-to-static efficiency of the turbine

the radii of the exducer exit given that the radius ratio at that location is 0.4.

  A cantilevered beam with a rectangular cross section

A cantilevered beam with a rectangular cross section is loaded by a force perpendicular to the beam center line at the free end. The cross section is 100mm high and 25mm wide. The vertical load at the beam end is 40,000N.

  Determine the centroidal moment of inertia

Determine the centroidal moment of inertia for the following. The center circle is cut out. you have a rectangle standing up ward the height is 7 in and the width is 4 in there is a cut out hole in the center with 2 in for diameter.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd