Calculate the time required to obtain a sample

Assignment Help Mechanical Engineering
Reference no: EM131171093

A grab sampler is used to collect a sample of pure gas. If the initial concentration of the gas in the sample volume is 0.5, and the volume and flow conditions are those of Prob. 13.10, calculate the time required to obtain a sample that is 99 percent pure.

Prob. 13.10:

A glass grab sampler has a volume of 125 cm3. Assuming a flow rate of 100 cm3/min, calculate the times required for 80, 90, 95, and 99 percent purge of the sampler.

Reference no: EM131171093

Questions Cloud

Compute the amount to be reported as income taxes : The difference is due to the use of different depreciation methods for tax and accounting purposes. The effective tax rate is 40%. Compute the amount to be reported as income taxes payable at December 31, 2010.
Which statements best describe an aggressive family : Which of the following statements BEST describe an aggressive family? Which of the following statements is NOT a commonly-held negative view of conflict
Fundamental reasons for succes - zara : The Fundamental reasons for success, with a comparison to another successful and an unsuccessful company - how can Zara maintain its competitive advantage, here the concept of sustainability may be introduced?
Estimated litigation expense : The estimated litigation expense of $2,000,000 will be deductible in 2015 when it is expected to be paid. Use of the depreciable assets will result in taxable amounts of $1,000,000 in each of the next three years. The income tax rate is 30% for al..
Calculate the time required to obtain a sample : A grab sampler is used to collect a sample of pure gas. If the initial concentration of the gas in the sample volume is 0.5, and the volume and flow conditions are those of Prob. 13.10, calculate the time required to obtain a sample that is 99 per..
Reconciliation between pretax financial income : Pole Co. at the end of 2010, its first year of operations, prepareda reconciliation between pretax financial income and taxable income as follows:
What has surprised you the most about mass communication : what has surprised you the most about Mass Communication content and why? Explain thoroughly. - How did you look at Mass Media prior to this class?
Calculate the time required to effect a 90 percent purge : Calculate the time required to effect a 90 percent purge of the sampler with a flow rate of 125 cm3/min.
What is the minimum product price : A perfectly competitive firm operates in the short-run with labor as its only variable factor. Its production function is: Q = -L3 + 10L2+ 88L where Q is output per week measured in tons and L is the number of workers employed. The weekly wage is ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Basically find dhdt and allow a value of h to be plugged

consider a thin walled cylindrical tank having a diameter of 2 ft and a height of 5 ft. the tank is initially filled to

  Develop an expression for as the water evaporates

Develop an expression for δ(x) as the water evaporates. Develop an expression for the maximum length of wetted plate, and provide a criterion for the laminar solution to be valid.

  Rate of heat removal per unit width of the fin

What is the rate of heat removal per unit width of the fin? Generate a plot of the heat removal rate per unit width of the fin for motorcycle speeds ranging from 10 to 100 km/h.

  In addition to driving the air compressor the turbine

an adiabatic compressor compresses air from atmospheric pressure and 70 degf at a rate of 10000 acfm actual cubic feet

  Determine the minimum power input

Air enters an adiabatic compressor at 0.1 kg/s, 100 kPa, 25 °C and exits at 700 kPa. (a) Draw a schematic of the system. Determine (b) the minimum power input (kW) and (c) the entropy generation rate (kW/K)

  When the pressure in the tank reaches 700 kpa the entire

3 rigid tank initially contains refrigerant-134a at 14oc. at this state 70 of the mass is in the vapour phase and the

  Parting line in injection molding

The parting line in injection molding is which one of the following: (a) the lines formed where polymer melt meets after flowing around a core in the mold, (b) the narrow gate sections where the parts are separated from the runner, (c) where the clam..

  A solution is poured into a conical filter of base radius

a solution is poured into a conical filter of base radius 12m and vertical height 15 m at a uniform rate of 8.4 m3s and

  Determine the heat and work associated with each process

a piston-cylinder device contains r-134a. initially the phase is saturated vapor at 160 kpa. the system then undergoes

  A 07-lb block rests on top of a 05-lb block supported by

a 0.7-lb block rests on top of a 0.5-lb block supported by but not attached to a spring of constant 9 lbft. the upper

  Derive the transfer function of this system with a

for a first order system with a transfer function of 15s2 given a unit step input pleasea. derive the transfer function

  The rectangular test section of material is slowly

The rectangular test section of material is slowly loaded with a 450 kN axial load. The original cross-section is 25 mm by 100 mm. The original length is 2 meters. Once fully loaded, the 100 mm side measures 99.96 mm and the length has increased by 2..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd