Calculate the reynolds number based on the wire diameter if

Assignment Help Mechanical Engineering
Reference no: EM13644179

A hot-wire anemometer is a temperature-based instrument for measuring velocities in a flowing gas. The key component of the device is a very fine wire (diameter = 0. 0004 in. , length = 0. 20 in. ) that is electrically heated. The wire is positioned so that the air stream passes over it in cross flow. The heating of the wire is accomplished by ohm ic dissipation of electric energy, in the same manner that the wires of a toaster are heated. The ohm ic heating of the wire is 0. 0253 W, and the wire temperature is 147 F. In the steady state, this heat is transferred to the air flow. The air that passes over the wire has a temperature of 73 F and a pressure of 726 mm Hg. Required results: The velocity of the air flow. Calculate the Reynolds number based on the wire diameter. If the velocity were to be doubled, and the wire and air stream temperatures were maintained as stated, what is the required ohm ic dissipation?

Reference no: EM13644179

Questions Cloud

A solution containing 1513 g of glucose in 1000g of water : a solution containing 15.13 g of glucose in 100.0g of water was found to freeze at -1.29c with a 1.53 cm. what is the
A 14- container of liquid nitrogen is kept in a closet : a 1.4- container of liquid nitrogen is kept in a closet measuring 1.2 by 1.2 by 1.9 . assuming that the container is
The action of an alkaline i2 solution on the rodenticide : the action of an alkaline i2 solution on the rodenticide warfarin c19h16o4 308.34 gmol results in the formation of 1
A 06407 g sample containing chloride and iodide ions gave a : a 0.6407 g sample containing chloride and iodide ions gave a silver halide precipitate weighing 0.4430 g. this
Calculate the reynolds number based on the wire diameter if : a hot-wire anemometer is a temperature-based instrument for measuring velocities in a flowing gas. the key component of
A vessel contains 090 g liq h2o in equilibrium with water : a vessel contains 0.90 g liq h2o in equilibrium with water vapor at 30c. at this temperature the vapor pressure of h2o
The enthalpy change when a strong acid is neutralized by : the enthalpy change when a strong acid is neutralized by strong base is -56.1 kjmol. if 135 ml of 0.450 m hi at
Find the specific turbine work using generalized charts and : an alternative energy power plant has carbon dioxide at 6 mpa 100 deg c flowing into a turbine and exiting as saturated
A pure gold ring and pure silver ring have a total mass of : a pure gold ring and pure silver ring have a total mass of 16.2 g. the two rings are heated to 64.8 c and dropped into

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd