Calculate the relative permeability of the iron

Assignment Help Electrical Engineering
Reference no: EM13266075

An iron core of cross-sectional area 200 square mm and length 320mm is evenly wound with a coil of 100 turns. When a current of 0.35A flows in the coil, a magnetic flux density of 0.12T is set up in the iron core. Calculate the relative permeability of the iron and the reluctance of the iron core.

Reference no: EM13266075

Questions Cloud

What is the angular speed of the molecule : A diatomic molecule is excited to its first rotational energy level, corresponding to J = 1. what is the angular speed of the molecule about its center of mass
Solitary confinement will prevent further corruption : One of the first prison systems was called the Pennsylvania System. The ideology of this system was used in the Eastern State Penitentiary in the early 1800s.
Find the energy of the second rotational state : Assume the distance between the protons in the H2 molecule is 7.50 multiply.gif 10-11 m. Find the energy of the second rotational state, with J = 2
Calculate the speed at which the armature must rotate : A four-pole armature is to generate an average e.m.f. of 2.0V per conducter, the flux per pole being 25mWb. Calculate the speed, in r/min, at which the armature must rotate.
Calculate the relative permeability of the iron : An iron core of cross-sectional area 200 square mm and length 320mm is evenly wound with a coil of 100 turns. When a current of 0.35A flows in the coil, a magnetic flux density of 0.12T is set up in the iron core.
Determine the value of brewsters angle : A light beam is incident on a piece of zircon (n = 1.923) at the Brewster's angle. determine the value of Brewster's angle
Find ratio of co2 emission when power comes from wind farms : If the emission, factor of producing electric power by PV cells is 100 g of CO2 per kWh, by wind power is 15 g of CO2 per kWh, and by coal is 1000 g of CO2 per kWh, then find the ratio of CO2 emission when a) 15% of power comes from wind farms
Should it replace the old steamer : What is the NPV of the project? Round your answer to the nearest dollar.
What are the discount yield and the true annual yield : What are the discount yield and the true annual yield on a six-month, $10,000 Treasury bill purchased for $9,589?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Describe a linear circuit which contains a voltage source

Suppose a linear circuit contains a voltage source and a current source. When the voltage source is set to 10V and the current source is set to 10 mA, the output voltage is 1V. When the voltage source is set to 10V and the current source is set to..

  What is the equilibrium hole concentration

A Si sample is doped with 10^17 As atoms/cm^3. What is the equilibrium hole concentration P0 at T=300K?

  What is the received bit pattern corresponding to part a

b) Draw the LFSR circuit to generate the CRC. Generate the CRC by applying the data pattern to the LFSR and verify the answer in part a. c) An error vector is given by X7+ X6+ X4+ X3+1. What is the received bit pattern corresponding to part a

  Determine the cross-sectional area of the core

A single phase transformer has the following rating: 120 kVA, 2000 V/100 V, 60 Hz with 1000 primary turns. Determine (A) the maximum flux. (B) given a maximum flux density of 0.25 T, the cross-sectional area of the core.

  Calculate the position of the fermi level

Boron donor atome at a concentration of 10^15 cm^-3 are distributed uniformley throughout a silicon sample. The sample is then also doped with 6*10^15 cm^-3 of phosphorous. calculate the position of the Fermi level

  Design an opamp circuit to perfom the operations

Design an opamp circuit to perfom the following mathmatical operations on three seperate ideal voltage sorces, V1, V2, and V3. V0 = 10V1 + 4V2 - 8V3

  Why has lead-free solder replaced lead-based solder

1. What is the purpose of core in hollow solder wire 2. What is tinning, and why is it important 3. Why is safety so important when soldering 4. Why has lead-free solder replaced lead-based solder. Be sure to properly cite any sources of information.

  What is the minimum sampling frequency for a/d conversion

A video signal contains light variations that change at a frequency as high as 3.5 MHz. What is the minimum sampling frequency for A/D conversion?

  Traffic light controller

The schematic of the traffic light controller

  What is the dc gain of the compensated closed loop system

Determine the phase margin of the uncompensated and compensated system from the Nichols chart. (The graph on the left is uncompensated, the one on the right is compensated. What is the DC gain of the compensated closed loop system.

  Determine sum of the largest two numbers and store its value

Assume that the memory locations M[$20], M[$21] and M[$22]. Write a 68HC11 assembly language program (with lots of comments) that will determine the sum of the largest two numbers and store its value in M[$23].

  Design the circuit using mfb topology

determine the transfer function of a 4th order lowpass butterworth filter with a 3-dB cutoff frequency of 3.4 kHz and passband gain=1. Design the circuit using MFB topology. Design two sections with an order of 2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd