Calculate the rate of change of heat with the cylinder

Assignment Help Mechanical Engineering
Reference no: EM13217157

For a vertical cylinder with an electric heater 2500watt at the base,an inlet(lower part of cylinder with cold water at 25C) and outlet(upper part of cylinder, with hot water @ 100C) flow channel, how do i calculate the rate of change of heat with the cylinder, and the vertical temperature distribution along the cylinder's wall.

Reference no: EM13217157

Previous Q& A

  What is the elastic modulus of the material

A beam of span 600mm has a load of 1 kg and deflects by 0.55mm its width is 25.4mm and depth is 6.7mm what is the elastic modulus of the material?

  Why is it important to protect intellectual property

Why is it important to protect intellectual property and how can intellectual property be protected and do intellectual protections ever go "too far"

  Determine the mass moment of inertia

A flywheel can be considered as being composed of a thin disc and a rim. The rim weighs 322 lb and has diameters of 24 in. and 30 in. The disc weighs 64.4 lb. Determine the mass moment of inertia about the centroidal axis about which the flywheel ..

  Explain what ethical leadership and management violation

What ethical leadership and management violation has Victor committed? Explain. What legal protection is available to John if he decides to inform the SSA about the software use? Explain.

  Determine the moment of p about a

a 13.2-N force P is applied to the lever which controls the auger of a snowblower. Determine the moment of P about A when alpha is equal to 30 degrees.

  How the federal reserve take to give the economy a boost

The Federal Reserve chairman acknowledges the economy is in a recession. What actions might the federal government and the Federal Reserve take to give the economy a boost? What are these policies called?

  Determine the velocity of molten metal flowing through

How do you determine the velocity of molten metal flowing through the base of the downsprue?

  Determine the maximum speed

Determine the maximum speed at which the car with mass m can pass over the top point A of the vertical curved road and still maintain contact with the road.

  What dielectric constant must the material between the plate

A simple plate capacitor can store 6.5x10^-5 C at a potential of 10000 V. what dielectric constant must the material between the plates have if their area is 6.0x10^-5 m2 and they are 0.16 mm apart?

  Explain disadvantages of several electronic communications

Write a paper in which you evaluate the advantages and disadvantages of several electronic communications and their potential uses with your internal audience. In considering your internal stakeholders,

Reviews

Write a Review

 

Similar Q& A

  Determine be naturak frequency of the system

A 0,5Kg mass attached linear spring suffress 01 N/m. Determine be naturak frequency of the system in hortz e reapert this calculation for a mass of 50Kg and a suffress of 10N/m and compare your result to that of part.

  Derive the linearised equation about the operation

For the pendulum shown in the figure,the restoring torque due to gravity is given by T=mgLsin(thita). Derive the linearised equation about the operation point thita=0.

  Determine the tensions at the cables

the suspended load exerts a force F=600 lb at A, and the weight of the bar OA is negligible. Determine the tensions at the cables and the reactions at the ball and socket support O

  Design a computer programme using freudestein equation

design a computer programme using freudestein equation to synthesise a four bar linkage using three precision points also using more than three points.

  What are the tensions in cables ef and eg

The system shown anchors a stanchion of cable-suspended roof. If the tension in cable AB is 900 kN, what are the tensions in cables EF and EG?

  State what the joints are in the system

State what the joints are in the system and knowledge of computational kinematics explain what you believe is the procedure to calculate each variable.

  Design a garage door controller using plc ladder diagram

Design a garage door controller using PLC Ladder Diagram (RSLOGIX 500 PLC SIMULATOR)

  Determine the pressure and the internal energy

refrigerant -134a at 800kPa and 25 C is throttled to a temperature of -20C. determine the pressure and the internal energy of the refrigerant at the final state.

  Solve for the pressure of a gas using both equations

Solve for the pressure of a gas using both equations at a temperature of 400K and a molar volume of 1x 10-4 m3/mol. For the van der Waals EOS, use parameters of a= 4.1x10-1 (m3/mol)2 Pa, and b=4.3x10-5 m3/mol.

  Entropy explained the temperature reaches

Entropy explained in this solution, Liquid H2O at 8 MPa and 40 degrees C is heated reversibly at constant pressure until the temperature reaches 600 degrees C

  Calculate the change in internal energy of the gas

Calculate the change in internal energy of the gas. Remember it is an ideal gas in a constant temperature bath.

  What power could be transmitted by a similar shaft rotating

If the maximum shear stress is limited to one-half of its yield strength and the fillet radius is 0.3 in, what is the maximum torque that can be applied? What power could be transmitted by a similar shaft rotating at 400 rpm?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd