User Account

All Pages

Calculate the porosity and the void ratio after shaking

Assignment Help Mechanical Engineering
Reference no: EM131242854

If the glas is shaken, it will be observed that the water level remains the same, but the level of the sand decreases. If this level now indicates a total volume of 128 cm3 , calculate the porosity and the void ratio after shaking.

Reference no: EM131242854

Questions Cloud

Calculate the porosity n of the sand : Calculate the porosity n of the sand. Also calculate the void ratio e.
Describe three to five functions of the agency : Provide background information about the agency and its department, mission, and its goals / objectives. (Title this section Introduction.) Describe three to five functions of this agency.
Investigates a specific natural disaster topic : Research Paper paper that investigates a specific natural disaster topic, apply critical thinking to the presentation of the information, and utilize and synthesize appropriate current research for your selected topic.
Conduct some research then write a short essay : Select a topic and conduct some research Then, write a short essay. - explain why you decided to research that topic;
Calculate the porosity and the void ratio after shaking : If the glas is shaken, it will be observed that the water level remains the same, but the level of the sand decreases. If this level now indicates a total volume of 128 cm3 , calculate the porosity and the void ratio after shaking.
Lowest level of organizations : Which type of departmentation is useful only at the lowest level of organizations?
What is the water content of the soil : Then the weight of the ring and the dry soil is found to be 380 g. The ring itself (empty and dry) weighs 210 g. What is the water content of the soil?
What is the concentration of chromium in river downstream : A facility discharges effluent containing chromium into a river. The effluent from the facility has a flow rate of 0.05 m3/s and has a concentration of 10 mg/L. What is the concentration of chromium in the river downstream from the facility
Emotion in negotiation : Conduct a light research on the role of emotion in negotiation process, and the effect it has on the outcome of the negotiation. In your essay, try to answer the following the questions:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The critical stress in mpa required for crack propagation

for a brittle material that has a crack of length 0.04mm and flexural strength and elastic modulus values of 88.1 mpa

  Calculate the extra separation at the saw cut

A steel ring of mean diameter 250 mm has a square section 2.5 mm by 2.5 mm. it is split by a narrow radial saw cut. the saw cut is opened up further by a tangential separating force of 0.2 N. calculate the extra separation at the saw cut. E = 200G..

  The nitrogen is compressed to frac12 of the initial volume

two kg of nitrogen at 40degc and 200 kpa are contained in a frictionless piston-cylinder device. the nitrogen is

  Derive an equation for the lines of constant declination

Derive an equation for the lines of constant declination in a sunpath diagram, for example, Figure 2.12. Check your equation by plotting a few declination lines on a piece of polar coordinate graph paper.

  Same length between supports as the length of the paper roll

A paper mill processes rolls of paper having a density of 984 kg/m3. The paper roll is 1.50 m outside diameter (OD) x 22 cm inside diameter (ID) x 3.23-m long and is on a simply supported, hollow, steel shaft. Find the shaft ID needed to obtain a max..

  Determine the rate of heat loss at the compressor exit

refrigerant 134-a enters a compressor as a saturated vapor at 200 kpa at a rate of 0.04 m3s. the power input to the

  Determine the rate of heat transfer from the bottom surface

consider a hot automotive engine which can be approximated as a 0.5-m-high 0.40-m-wide and 0.8-m-long rectangular

  How long after it starts does the motorcycle reach the

the combined mass of the motorcycle and rider is 160 kg. the motorcycle starts from rest at t 0 and moves along a

  Evaluate thermal efficiency of the cycle

Evaluate thermal efficiency of the cycle

  Convective heat transfer coefficient

An aluminium casting 2 cm cubed is at 800 degrees Celsius and is to be air quenched in 30 degree Celsius air having convective heat transfer coefficient of 50 W/m^2*k determine

  Mechanical waves need a medium to propagate.

Electromagnetic waves (which transfer electromagnetic energy) do not need any medium to propagate. EM waves travel forward due to vibrations of the electric field and magnetic field vectors. Example : Light waves are EM waves.

  Air enters an automotive supercharger

Air enters an automotive supercharger at 100 kPa and 300 K and is compressed to 150 kPa. the efficiency is 70%. What is the required work input per kg of air?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd