Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A four-pole dc generator has magnetic flux of 0.06 Wb/pole, a rotational speed of 1800 rpm, full load current of 40 A, and is simplex lap wound. The generator efficiency is 91%. Pole face coverage is 78%. Calculate:
A. The number of conductors needed for Vout= 250 V at no load. (recall φ= BA)B. The maximum armature current capacity of the generator.C. The armature resistance (RA) if the load voltage is 240V at maximum armature current capacity.
The parameters of a certain transmission line operating at ω = 6×108 rad/s are L = 0.35μH/m, C = 40 pF/m, G = 75 μS/m, and R = 17 Ω/m => α=0.0943 Np/m, β=2.2467 rad/m, λ=2.7966 m, Z0 =93.623-j3.6368
Supposed that the terminals are labeled a,b. V(ab) = -15 V, how much energy is exchanged when a positive charge of a 4 C moves through the device from a to b. Is the energy delivered or taken from the device.
Ted Williams hits a baseball with an initial velocity of 120 miles per hour (176 ft/s) at an angle of f = 35 degrees to the horizontal. The ball is struck 3 feet above home plate. You watch as the ball goes over the outfield wall 420 feet away
Discuss the trade-offs between fiber optic and satellite communication in terms of costs, signal capacity, signaling method, interference, likelihood of failure and repair issues, multipoint capability, reconfiguration capability, and noise.
The main mission of this project is to design and build a tap changer which is going to be fitted to power transformers for regulation of the output voltage to required levels for the Micro Grid. The tap changer system will consist of 9 changers with..
consider the set of activities, duration (in days), and predecessors for a project given below. a) Develop a network diagram representation for the project. b) Determine the critical path. c) Determine the float time for all activities that are not o..
(1) check a diode out with a regular ohm meter (2) Give an example of where a half wave, full wave or bridge rectifier is used. (3) What sizes of transformers are used for power lines
A 60-Hz, single-phase transmission line has a length of 80 miles. Its shunt conductance (G) is 3.4×10?11 S/mile, resistance (R) is 0.1 ?/mile, capacitance (C) is 16 pF/mile, and inductance (L) is 0.56 mH/mile 220 kV, 220 MVA with power factor
The above transformer is to be connected as an auto transformer to supply a load at 120 V from 210 V source. What kVA load can be supplied without exceeding the current rating of the windings
A linear-phase FIR filter should be designed with the ideal magnitude response shown in Figure 1 which represents an narrow band-pass filter. The lower cutoff frequency, fL , is 2,000 Hz, and higher cutoff frequency, fH , is 3,600 Hz.
Design a buck converter to produce an output voltage of 18 V across a 10- load resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current.
Write an algebraic expression for S3, the forth sum bit of a binary adder, as a function of inputs x0, x1, x2, x3, y0, y1, y2, and y,3. Assume that c0=0, and do not attempt to "multiply out" or minimize the expression.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd