Calculate the new pressure of the gas

Assignment Help Mechanical Engineering
Reference no: EM13713250

A 3-Litre vessel contains gas at a pressure of 200 kPa. Five litres of gas at the same pressure is forced into the vessel. Calculate the new pressure of the gas. Use V1 = 8L, V2 = 3L

Reference no: EM13713250

Questions Cloud

Vapor power plant operates at steady state : A well-insulated tank in a vapor power plant operates at steady state. Water enters at inlet 1 at a rate of 125lb/s at 14.7lbf/in^2. Make up water to replenish steam losses from the plant enters at inlet 2 at a rate of 10 lb/s at 14.7 lbf/in^2 and 60..
Rate of heat transfer to the steam in the reheater : Air enters a compressor at 105 kPa and 300 K with a volumetric flow rate of 12 m3 /min and exits at 1200 kPa and 400 K. Heat transfer occurs at a rate of 2 kW from the compressor to its surroundings. Assuming ideal-gas behavior for air, steady flow, ..
What net torque must be applied to the wheel : A small grinding wheel has a moment of inertia of 4.0×105kg.m2. What net torque must be applied to the wheel for its angular acceleration to be 150rad/s2.
Steam enters the high-pressure turbine : In a reheat-cycle power plant, steam enters the high-pressure turbine at 5 MPa, 450°C, and expands to 0.5 MPa, after which it is reheated to 450°C. The steam is then expanded through the low-pressure turbine to 7.5 kPa. Liquid water leaves the conden..
Calculate the new pressure of the gas : A 3-Litre vessel contains gas at a pressure of 200 kPa. Five litres of gas at the same pressure is forced into the vessel. Calculate the new pressure of the gas. Use V1 = 8L, V2 = 3L
Air enters an automotive supercharger : Air enters an automotive supercharger at 100 kPa and 300 K and is compressed to 150 kPa. the efficiency is 70%. What is the required work input per kg of air?
Diamond shaped airfoil oriented to the oncoming stream : Consider a diamond shaped airfoil oriented to the oncoming stream. Approximate results since the inclination angles are small. All four faces are same length. Angle of attack is 10 deg. According to Newtonian hypersonic theory, Find the numerical val..
What is the electonic field at 9cm from the center : What is the E- field 9cm from the center along the symmetry axis of a charged ring with Q=25nC and R=12cm Let k= 9x109
Developed a power cycle rejecting heat into a cold reservoir : An inventor claims to have developed a power cycle rejecting heat into a cold reservoir at 300 K. If it is claimed that the thermal efficiency is 40%, evaluate the claim if the hot reservoir is at a) 800 K, b) 300 K and c) 600 K.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A j type thermocouple referenced at 70f has a measured emf

a j type thermocouple referenced at 70f has a measured emf of 2.878mv. what is the tempature of the measured

  Determine the reversible power input

A refrigerator is maintained at 5°C by removing heat from the refrigerated space at 18,000 kJ/hr. The power input to the refrigerator is 1500 W and the surrounding air is at 36° C.

  What is a column what factors determine the amount of load

1.what is a beam? what factors determine the maximum load that it can take without failure?2.what is a column? what

  A refrigerator cycle has a cop of 3 and removes 100kw of

a refrigerator cycle has a cop of 3 and removes 100kw of heat from a building which is kept at 23c. the device rejects

  Unidirectional reinforced composites

Calculating the mechanical properties of unidirectionally reinforced composites

  The experiment is repeated with a metallic sphere of the

a small sphere of reference-grade iron with a specific heat of 447 jkgk and a mass of 0.515 kg is suddenly immersed in

  Calculate the change in the enthalpy and the change in

1. the initial state of one mole of a monatomic ideal gas is p10 atm and t300k. calculate the change in the entropy of

  Determine the exergy of the energy assuming an environment

consider a large furnace that can supply energy in the form of heat at 2000 r at a steady rate of 3000 btus. determine

  What is the normal stress on a plane whose normal makes an

given the following stress components sigma x 12000 psi sigma y 8000 psi sigma z -6000 psi sigma xy 9000 psisigma yz

  Determine the maximum load that can be carried by the

a tensile member of aluminum alloy 2024 - 0 had an original cross - sectional area of 4. 0 square inches. if the strain

  The local shear stress measured at the surface of the plate

a turbulent boundary layer exists in the flow of water at 20degc over a flat plate. the local shear stress measured at

  If the two coils are replaced by reistors of equivalent

a coil of 12 ohms is connected in parallel with another of 20 u ohms resistance the circuit is then connected in series

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd