Calculate the natural frequency requirements

Assignment Help Electrical Engineering
Reference no: EM131171772

A second order instrument is required to measure the input signals up to 100Mz with an amplitude inaccuracy of less than 1%. Calculate the natural frequency requirements, if the damping ratios are 0.3 and 0.6 respectively. Determine the phase shift in each case at 50 and 75Hz

Reference no: EM131171772

Questions Cloud

Support of value added tax for the federal government : Which of the following might logically be reasons used in support of a value added tax for the federal government?Improve separation of revenue sources across the levels of government (federal, state, and local). Provide an increased economic incenti..
Compare three performance measurement practices : Compare three performance measurement practices. Determine appropriate financial compensation and rewards using the scenario from your assignment and explain your rationale of selecting the financial compensation and rewards.
What factors cause a contraction in commercial paper market : What factors contribute to an expansion of the commercial paper market? - What factors cause a contraction in the commercial paper market?
States apply high excise tax rates on cigarettes : States apply high excise tax rates on cigarettes. Which of the following is an accurate statement about such taxes?
Calculate the natural frequency requirements : Calculate the natural frequency requirements, if the damping ratios are 0.3 and 0.6 respectively. Determine the phase shift in each case at 50 and 75Hz
Describe a new fictitious product idea : Describe a new fictitious product idea that you believe would be a logical fit for your chosen organisation and its brand promise as well as commercially successful in a new international market of your choice.
The trends and fluctuations in the unemployment rate : Describe (briefly) the trends and fluctuations in the unemployment rate in the United States from 1949 through 2013. In which periods was the unemployment rate above average and in which periods was it below average?
Explain the principle value of two vision statements : Explain the principle value of two vision statements. Explain the principle value of two mission statements. Compare and contrast vision statements of each organization in terms of composition and importance.
Confidence interval for the proportion : When 300 junior college students were surveyed, 145 said they have a passport. construct a 95% confidence interval for the proportion of junior college students that have a passport.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Write phasor expression i for current using cosine reference

Write the phasor expression I for the following current using a cosine reference a.)i(t) = I0cos(ωt - π/6): b.) i(t) = I0sin(ωt + π/3):

  Construct 4-to-16-line decoder with five 2-to-4-line decoder

Construct a 4-to-16-line decoder with five 2-to-4-line decoders (74LS139A). Use a block diagram for components and clearly show your address select variables.

  You are asked to determine the signal-to-interference

you are asked to determine the signal-to-interference ratio sir or ci on the forward link of a cellular system when

  What is the main cause of bit errors on this digital link

What is the main cause of bit errors on this digital link? At the receiver, what is the rule that is used to decide whether to output a 1 or a 0?

  What is the relationship between base and collector current

For an ideal Zener, is the Zener voltage is 15v and the power rating is 750mW, what is the maximum zener current allowed What is the relationship between base current and collector current called Show the equation relating IC IB and IE

  An air-cored torus with a square cross section

A coil of 5000 turns is wound in the form of an air-cored torus with a square cross section. The inner diameter of the torus is 60 mm and the outer diameter is 100 mm. The coil current is 0.25 A.

  Calculate what is the temperature

The volume of a gas is 20 cc at 27°C. Pressure remaining constant. What is the temperature at which the volume of gas becomes 40 cc

  Calculate the starting torque and current

an induction motor when connected in delta and started direct on line produces a starting torque of 60Nm and consumes 80A. if the same motor is started using the soft start equipment with the voltage set at 0.8 of the line

  What is the torque when the antenna gets to within 5 degrees

A proportional controller for a rotating antenna has a gain Kp of 5 in-oz/deg. The antenna was initially pointing due south, but was then commanded to point southeast. What is the torque when the antenna gets to within 5o

  Find average power loss in line before and after load added

The power factor of the added load is to be adjusted so that the overall power factor of the factory is 0.96 lagging. The factory is fed from a line having an impedance of 0.02 + j0.16 O. The voltage at the factory is maintained at 480 V(rms).

  Why phasor analysis can only be performed on single-freq ckt

Discuss why phasor analysis can only be performed on single-frequency circuits. For multiple frequencies what type of analysis must be performed.

  Calculate the received power and the path loss

Calculate the received power and the path loss. Assuming this is the maximum acceptable path loss for the system, how does the maximum system range change at 1 GHz and 10 GHz, assuming all other parameters remain constant

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd