Calculate the mole fractions dry basis and the ppm parts

Assignment Help Mechanical Engineering
Reference no: EM13631761

The ultimate analysis of a No.4 fuel oil is 86.47 wt% carbons. 11.65% hydrogen, 1.35% sulfur, and the balance noncombustible inerts this oil is burned in a steam-generating furnace with 15% excess air. The air is preheated to 175°C and enters the furnace at a gauge pressure of 180 mm Hg. The sulfur and hydrogen in the fuel are completely oxidized to SO2 and H2O: 5% of the carbon is oxidized to CO. and the balance forms CO2.

(a) Calculate the feed ratio (m3 air) / (kg oil).

(b) Calculate the mole fractions (dry basis) and the ppm (parts per million on a wet basis, or moles contained in 106 moles of the wet stack gas) of the stack gas species that might be considered environmental hazards.

Reference no: EM13631761

Questions Cloud

Draw a free body diagram of the spring cut near the point a : a coil spring is stretched by two equal and opposite forces f120n. the wire diameter is 5 mm and the mean coil diameter
A gas turbine burns methane with 150 theoretical air : a gas turbine burns methane with 150 theoretical air. assume the air is 25 degrees celsius 100 kpa and has a relative
A 350 cm diameter coil consists of 30 turns of circular : a 35.0 cm diameter coil consists of 30 turns of circular copper wire 2.0 mm in diameter. a uniform magnetic field
A well-insulated rigid tank contains 5 kg of a saturated : a well-insulated rigid tank contains 5 kg of a saturated liquid-vapor mixture of water at 150 kpa. initially
Calculate the mole fractions dry basis and the ppm parts : the ultimate analysis of a no.4 fuel oil is 86.47 wt carbons. 11.65 hydrogen 1.35 sulfur and the balance noncombustible
An airline company is considering a new policy of booking : an airline company is considering a new policy of booking as many as 281 persons on an airplane that can seat only 270.
The central maximum of a single-slit diffraction pattern : the central maximum of a single-slit diffraction pattern has a width of 2.00 cm when measured on an observing screen
A 4 lb block with an initial velocity of 5 fts is sliding : a 4 lb block with an initial velocity of 5 fts is sliding down a 30 degree slope before being slowed by a spring. if
Use normal approximation to estimate the probability of : use normal approximation to estimate the probability of getting exactly 47 girls in 100 births. assume that boys and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the total rate of exergy destruction that would

steam at 3mpa and 700 degrees c is available at one location in an industrial plant. at another location steam at 2mpa

  What is the spring rate of each what force is required to

two steel compression coil springs are to be nested. the outer spring as an inside diameter of 1.5 in a wire diameter

  One would like to find preheat 2 tons h of a solution with

one would like to find preheat 2 tons h of a solution with a specific heat capacity of 3.35 kj kg k from 15 c to 70

  The uniform slender bar abc weighs 6 lb and is intially at

the uniform slender bar abc weighs 6 lb and is intially at rest with end a bearing against the stop in the horizontal

  The heat engine is to generate 370 kw if the mass flow rate

geothermal steam is planned as an energy source for power generation. the steam enters and adiabatic exchanger at 2

  A rod has a cross sectional area of 1 cm2 its material has

a rod has a cross sectional area of 1 cm2. its material has the following strength properties beyond which it breaks

  By how much will the bullets miss the target

a hunter aims directly at a target 140 meter away. if the bullet leaves the gun ay a speed of 280 m/s, by how much will the bullets miss the target?

  Pin a which is attached to link ab is constrained to move

pin a which is attached to link ab is constrained to move in the circular slot cd. knowing that at t0 the pin starts

  Compute the torsional shear stress in a hallow shaft with

compute the torsional shear stress in a hallow shaft with an outside diameter of 40 mm and an inside diameter of 30 mm

  If the inner and out radii of the shell are r1 5cm r2 6

a spherical shell made of a material with a density of 1600 kgm3 is placed in water. if the inner and out radii of the

  A l-shaped bracket lying in a horizontal plane supports a

a l-shaped bracket lying in a horizontal plane supports a load p as shown. the bracket has a hollow rectangular cross

  Brayton gas turbine cycle has two stages of compression

A Brayton gas turbine cycle has two stages of compression and two stages of expansion. The pressure ratio across each stage of the compressor and turbine is 3. The air enters each stage of  the compressor at 300K and each stage of the turbine at 1..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd