Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Suppose a signal from a vibrating motor is to be sampled discretelywith a digital data acquisition system to determine the RPM of the motor. It is known that the maximum possible RPM is 1800.
A. What is the minimum sampling frequency (in Hz) with which thesignal can be sampled in order to measure the RPM of the motor?From Nyquist criterion, the sampling frequency fs must begreater than 2fmax so fs > 60 Hz.
B. For the same conditions above, suppose that the RPMneeds to be known to within a precision of +1 RPM. Calculate the minimum number of discretely sampled data points necessary to achieve this resolution.
Explain the characteristics of electromagnetic waves and application to communications systems and determine the signal spectra for the content of complex waveforms
A BJT is operated in a 50ohm circuit 1.5Ghz. FOr the bias conditions of Collector Current - 4mA and Collector-Emittor Voltage = 10V. The manufacturer provides the S-parameters in magnitude and angles (in degrees) as follows. S11 = 0.7
The two blocks in the figureoscillate on a frictionless surface with a period of 1.7 s. The upper block just begins to slip when the amplitude is increased to 32cm. What is the coefficient of static friction between the two blocks
Which of the following is not an advantage of SPI transmission over SCI transmission Error checking via parity bit Faster transmission Master-slave capability Synchronous transmission A HCS12 embedded timer is in PWM mode.
Compute the inverse Fourier transform for X(ω) = cos 4ω. 5. A signal with the highest frequency component at 10 kHz is to be sampled. To reconstruct the signal, the sampling must be done at a minimum frequency of?
What should the signal definitions be for the equations, such that the minimal about of hardware (gates) are used assuming we have an abundance of NAND gates Show the signals definitions and resulting circuitry.
a. Given a circuit with a VCVS (A=1000) in series with a 100K ohm resistor, convert this circuit to a VCCS in parallel with a resistor R. b. Connect both circuits to a 25K ohm load resistor and show they produce the same behavior in the load resis..
A simple RC filter is to be designed to pass frequencies below a nominal value of 40 Hz. If the attenuationat 40 Hz is to be 5 dB, determine suitable values of R and C for the filter.
A D'Arsonval meter movement is described by its fullscale current Ifs and full scale voltageVfs , with Vfs= 100mV andIfs=10mA . Determine the resistanceRm of the D'Arsonval meter movement.
A modulating signal is amplified by a 80% efficiency amplifier before being combined with a 20 kW carrier to generate an AM signal. what would be The required DC input power to the amplifier, for the system to operate at 100% modulation.
a. Implement both functions with one 3:8 decoder and logic gates. b. Implement both functions with one or more 8X1 muxes (and logic gates if needed) c. Implement both functions with 2X4 decoders and logic gates.
The load draws 1.2 pu current at 0.6 puvoltage while drawing 0.5 pu (true) power. If the base volageis 20 kV and the base current is 160 A, calculate the power factor and the ohmic value of the resistance of the load.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd