Calculate the maximum tensile stress tmax

Assignment Help Mechanical Engineering
Reference no: EM131062094

A post having a hollow circular cross section supports a horizontal load P = 240 lb acting at the end of an arm that is 5 ft long (see figure). The height of the post is 27 ft, and its section modulus is S = 15 in.3 Assume that outer radius of the post, r2 = 4.5 inches, and inner radius r1 = 4.243 inches.

(a) Calculate the maximum tensile stress τmax and maximum in-plane shear stress τmax at point A on the outer surface of the post along the x-axis due to the load P. Load P acts in a horizontal plane at an angle of 30° from a line which is parallel to the (-x) axis.

(b) If the maximum tensile stress and maximum inplane shear stress at point A are limited to 16,000 psi and 6000 psi, respectively, what is the largest permissible value of the load P?

2016_d144762e-d3dd-4860-872f-6f9d228decff.png

Reference no: EM131062094

Questions Cloud

What mass of melamine : What mass of melamine, C3N3(NH2)3, will be obtained from 101.5 kg of urea,CO(NH2)2, if the yield of the overall reaction is 72.0%?
Determine the maximum in-plane shear stresses : Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points A, B, and C, located on the outer surface at the base of the pipe.
Unsuitable for drinking due to high concentration : The concentration of fluoride, lead, nitrate and iron in a water sample from an underground lake was found to be 1000 ppb, 40 ppb, 100 ppm and 0.2 ppm, respectively. This water is unsuitable for drinking due to high concentration of : (1) Lead (..
How will you incorporate the animation from the film : What will the guests see/do after they leave the attraction? Why? How will you reinforce the experience and entice them back? Provide a 300 word narrative with three images/sketches (solos one image).
Calculate the maximum tensile stress tmax : Calculate the maximum tensile stress τmax and maximum in-plane shear stress τmax at point A on the outer surface of the post along the x-axis due to the load P. Load P acts in a horizontal plane at an angle of 30° from a line which is parallel to ..
Modify the console application to test it out : Modify the console application to test it out. Can add a for loop to pick out a random bar from the three, make sure as you go through the loop.
Estimate the equilibrium constant : Using standard electrode potentials calculate ΔG and use its value to estimate the equilibrium constant for each of the reactions at 25 °C. Br2(l)+2Cl-(aq)→2Br-(aq)+Cl2(g) and MnO2(s)+4H+(aq)+Cu(s)→Mn2+(aq)+2H2O(l)+Cu2+(aq)
Metabolism from the liver with a half-life : Metformin is used to treat Type II Diabetes. It is excreted in the urine with no metabolism from the liver with a half-life of 5 hours. Average Volume of Distribution of Metformin is 654 L for a dose of 850 mg.
Create two different confidence interval estimates : The purpose of this assignment is to collect and organize a random sample of data values and then create two different confidence interval estimates of the population mean. The information will then be analyzed in a written summary.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd