Calculate the maximum eccentricity e for zero tension

Assignment Help Mechanical Engineering
Reference no: EM131382030

For the pedestal of given Problem, assume that the load is placed at the computed eccentricity. Calculate the maximum tensile and compressive stresses developed on a horizontal plane 3 ft below the top of the pedestal

Problem
A concrete pedestal is in the shape of a cube and is 6 ft on each side. The pedestal supports a superimposed load of 40,000 lb located on the Y-Y axis, as shown. Calculate the maximum eccentricity e for zero tension at the base of the pedestal. Include the weight of the pedestal using a concrete unit weight of 150 pcf.

2454_Fig 01.jpg

Reference no: EM131382030

Questions Cloud

Calculate the maximum eccentricity e for zero tension : Calculate the maximum eccentricity e for zero tension at the base of the pedestal. Include the weight of the pedestal using a concrete unit weight of 150 pcf.
Provide in relation to business performance : recommend one approach that an accountant could take in order to measure the types of complexity you identified for a specific business or industry and determine the insight that the measure will provide in relation to business performance.
Identify and discuss compliance risks : For this part of the assignment, you will add the following topics to your training manual: Identify and discuss 3 compliance risks. Indicate the consequences of not meeting these requirements
Difference between revenue and cost : If profit is the difference between revenue and cost, can you determine a profit function P(x) from these two lines? Show work for credit. Give an interpretation the $5000 found in the cost function. What do you think it could represent?
Calculate the maximum eccentricity e for zero tension : Calculate the maximum eccentricity e for zero tension at the base of the pedestal. Include the weight of the pedestal using a concrete unit weight of 150 pcf.
Design of health promotion programs : Design of health promotion programs including four phases (diagnosis, programme development, implementation, and evaluation): Identify program objectives
Conforming to university rules : University rules require that at least one in-state student and at least one senior hold one of the three offices. Note that if individuals change offices, then a different selection exists. In how many ways can the officers be chosen while still ..
Analyze the results in terms of success or failure : What was your marketing strategy for each of the decisions entered into the simulation game in Quarter #1?What were the results of your decisions?Analyze the results in terms of success or failure.What changes will you make in future quarters?
What’s the probability that molly will pass statistics : At the end of the semester, we find out that Molly failed. What's the probability that she got Professor Kurtosis?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the energy recoverable as heat per decay in mev

An alpha-emitter, has been used as a thermal power source, as described in Table 12.2. What is the energy recoverable as heat per decay in MeV? Provide two answers, one assuming all of the energy produced is dissipated as heat, and one assuming only ..

  Highspeed flows-typically consists of two cylindrical volume

A hypersonic gun tunnel is used to generate short-duration, high-speed flows and typically consists of two cylindrical volumes separated by a diaphragm. One end of the tunnel (the driver end) is pumped to a high pressure, while the other end (the dri..

  In a mechanical coal-washing process a portion of the

in a mechanical coal-washing process a portion of the inorganic sulfur and ash material in the mined coal can be

  A 40-mph wind below past your house speeds up as it flows

a 40-mph wind below past your house speeds up as it flows up and over the roof.nbspif the elevation effects are

  What prototype velocity corresponds to a model velocity

The design of a river model is to be based on Froude number similarity, where the Froude number, Fr = V/(gy)1/2 is a function of the water velocity, V, the water depth, y, and the acceleration of gravity, g. If the river depth is 3 m and the m..

  A pontoon of constant rectangular cross section is 50 m

a pontoon of constant rectangular cross section is 50 m long 10 m wide and 5 m in depth. it floats in sea water at a

  A piping system consists of 100 ft of 2-in pipe a sudden

a piping system consists of 100 ft of 2-in pipe a sudden expansion to 3-in pipe and then 50 ft of 3-in pipe. water is

  Lifting cylinder in cross flow of radius

Given a lifting (rotating) cylinder in cross flow of radius a with a lift coefficient of C1=5, calculate the peak (suction) pressure coefficient, Cp. Use potential flow relations and assume 2-D.

  The wheel roles without slipping such that at the instant

the wheel roles without slipping such that at the instant shown it has an angular velocity and angular acceleration.

  What is the elevator acceleration

A person conducts an experiment in which he rides in an elevator while standing on a set of scales that displays his weight in pounds (Fig. a). Let a be the elevator's upward acceleration rela tive to the earth. T

  Calculate the mass of the piston

A constant pressure is applied to a 0.5 m diameter vertical cylinder of 300 kPa in a piston cylinder device. Atmospheric pressure is 100 kPa. Calculate the mass of the piston and the work needed to move the piston 5 m in the upward direction.

  An angled jet of water comes from the ground at 5 m s at a

an angled jet of water comes from the ground at 5 m s at a 35 degree angle from the horizontal. how high does the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd