Calculate the lower radiation intensity threshold

Assignment Help Electrical Engineering
Reference no: EM131409908

A TGS plate of uniform thickness (30 µm) receives a uniform radiation flux for 1 ms at normal incidence. Using data given in Table 7.1, calculate the lower radiation intensity threshold, given that a change in voltage of 1 nV on the pyroelectric element can be detected.

1892_80b87658-1280-4009-9cbe-5c4c7fc2ec86.png

Reference no: EM131409908

Questions Cloud

Research the marketing of wentworth metro college products : BSBMKG502 Establish and Adjust the Marketing Mix Assessment - Research, case study and report. You are a student of Wentworth Metro College, use your knowledge, skills and own experiences to help answer the below question. Research the marketing of W..
Determine the expected value of perfect information : For the following payoff table, determine the expected value of perfect information. Does the result seem unusual? If so, why did this occur?
Develop a decision tree for jerry and help him to decide : Steve's Mountain Bicycle Shop is considering three options for its facility next year. Steve can expand his current shop, move to a larger facility, or make no change. With a good market, the annual payoff would be $76,000 if he expands, $90,000 i..
What is the cell density in the original sample : A nutrient agar plate labelled 10^(-5)ml had 154 colonies after incubated. what is the cell density in the original sample
Calculate the lower radiation intensity threshold : A TGS plate of uniform thickness (30 µm) receives a uniform radiation flux for 1 ms at normal incidence. Using data given in Table 7.1, calculate the lower radiation intensity threshold, given that a change in voltage of 1 nV on the pyroelectric e..
What is value-based management : Discussion: Value-based Management- What is value-based management? How can a company use value-based management techniques to make the best management decisions?
Characterization of the wife of bath : Based on the characterization of the wife of bath why do you think was Chaucers view of women and women roles
Which route will fred select if he uses maximin criterion : Assuming that shorter transit times are more desirable, which route will Fred select if he uses the maximin criterion? The maximax criterion? The minimax regret criterion?
Explain the components of the academic health centers : Describe the components of the academic health centers and their significance to the evolution of the university-based health professional education complex.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the swr on the line and the reflection coefficient

A lossless transmission line of electrical length l = 0.3? is terminated with a complex load impedance . Find the reflection coefficient at the load, the SWR on the line, the reflection coefficient at the input of the line

  Determine the fundamental frequency a periodic signal

A. Determine the fundamental frequency w0, the period t0, and the coefficients in the representation X(t) = x0 + Re{(sigma)k=1N Xkejkwot} for the above input.  C. Now consider a new signal y(t) = x(t) + 10 cos (50 pi t - pi/6). How is the spectrum ..

  What are the values of current gain and voltage gain

A current amplifier with R=9 kohm Ro=1 kohm and Ais=100 is connected between a 8 V voltage source with a source resistance of Rs=1 Kohm and a load resistance of RL=9 Kohm.

  Find the potential within the channel

Potential in infinite channel. The geometry in Figure 5.49 is made of a semi-infinite channel bounded by the planes x = 0, x = ∞, y = 0, y = b. Three sides are held at zero potential and the fourth is isolated from the others (between y = 0 and y ..

  Using the schematic design entry method design a logic

using the schematic design entry method design a logic circuit that has two 2-bit inputs x and y a 1-bit input

  Design and test a 4-bit ripple carry adder

Design and test a 4-bit ripple carry adder, i. e., an array of 4 full adders, that adds any 4-bit binary number A3A2A1A0 to the 8-4-2-1 BCD code of the third and fourth non-zero and different digits of your Red ID number.

  How much power is delivered to the end of the combined fiber

Ten multimode glass fibers (n1 = 1.48, n2 = 1.45) are spliced together. Each fiber is 2 km long and has a loss rate 2-dB/km. Each splice adds 1 dB of loss. If the output power of the source is 7 dBm and radiates uniformly in a 60 degree half cone

  Find the input power and power factor

Determine the input power and power factor when the link delivers 60 kW at 0.8 PF lagging at 2300 V.

  Explain conditions for rigid-body equilibrium

Explain conditions for Rigid-Body Equilibrium with relevant diagrams.

  Find what is real power consumed by the impedance

Find the real power and reactive power dissipated in an impedance Z = 2 ohm at zero degree carrying a current of I = 6 + j8 A. What is real power consumed by the impedance

  Calculate the mass of agcl required and give effective area

Design an Ag/AgCl electrode that will pass 150 mC of charge without removing all the AgCl. Calculate the mass of AgCl required. Show the electrode in the cross section and give the active area.

  Design a system by which the gears are shifted

The SCR in Figure requires a 4-V trigger. Design a system by which the gears are shifted when a CdS photocell resistance drops below 2.5 kΩ.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd