Calculate the longitudinal engineering strain

Assignment Help Mechanical Engineering
Reference no: EM13212834

A paper clip is made of wire 0.7 mm in diameter. If the original material from which the wire is made is a rod 25 mm in diameter, calculate the longitudinal engineering strain and true strain that the wire has undergone during processing.

Reference no: EM13212834

Questions Cloud

Explain what is the mole fraction of a in the solution : The mole fraction of A in the vapor is found to be 0.67. What is the mole fraction of A in the solution?
What is the energy of the transition : CO exhibits an infrared absorption band at 2143 cm^-1 that is attributed to the symmetric stretching transition. Assuming this corresponds to a transition from the v=0 to v=1 vibrational quantum number
What is the percent span for the old and new setpoints : a reactor setpoint wasincreased from 160 psig to 190 psig. the reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig. what is the percent span for the old and new setpoints?
Calculate the longitudinal engineering strain : A paper clip is made of wire 0.7 mm in diameter. If the original material from which the wire is made is a rod 25 mm in diameter, calculate the longitudinal engineering strain and true strain that the wire has undergone during processing.
Calculate the longitudinal engineering strain : A paper clip is made of wire 0.7 mm in diameter. If the original material from which the wire is made is a rod 25 mm in diameter, calculate the longitudinal engineering strain and true strain that the wire has undergone during processing.
What is the energy of the transition : CO exhibits an infrared absorption band at 2143 cm^-1 that is attributed to the symmetric stretching transition. Assuming this corresponds to a transition from the v=0 to v=1 vibrational quantum number
What two maintained tools will hurt an automotive technician : what two maintained tools will hurt an automotive technicians on the job performance?
Does either individual have a comparative advantage : The following numbers measure the tradeoff between grades and income: Total Hours Hours Hours Studying GPA Working Income 60 60 4.0 0 $ 0 60 40 3.0 20 $100 60 30 2.0 30 $150 60 10 1.0 50 $250 60 0 0.0 60 $300 Total Hours Hours Hours Studying GPA
What can be said about the expected defect rate : Given that the nominal diameter (per print) is 15.00mm +/-0.10mm, what can be said about the expected defect rate?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the stress in a stay at a given temperature

Determine the stress in a stay at a given temperature. A steel 'stay' of effective length 5m is fitted in between the walls of a ships refrigerated compartment when the temperature is 18 degrees centigrade.

  Find the stoichiometric air/fuel ratio of benzene

Please find the stoichiometric air/fuel ratio of benzene (C6H6) and the actual air fuel ratio when operated at equivalance ratio of 0.8.

  The dugdale model

Solve the problem in the image. Do it step wise in detail. This question is from book "Fracture Mechanics - An Introduction - E. Gdoutos Springer (Page 74)"

  Design value for the molded friction material and steel disk

Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?

  Temperature and density of air for an adiabatic process

Effect of pressure on temperature and density of air for an adiabatic process, The pressure is to be raised from atmospheric to 7 psi (4.83 bar). The process is adiabatic, and the volume is constant and unknown.

  Calculate the power output in kw

Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.

  Diameter pipe is used to maintain a constant level

Find flow rate A siphon made of a 1 in-inside-diameter pipe is used to maintain a constant level in a 20 ft-deep tank

  Define centrifugal clutch

Centrifugal Clutch Question, In a centrifugal clutch there are eight shoes, each of mass 0.3 kg and the centre of gravity of each shoe is at 50 mm radius when it is just touching the drum of diameter 200 mm.

  Determination of the heat transfer coefficient values

this would provide you with a set of Reynolds numbers. Next, using the integral method, determine the velocity profiles within the boundary layer to be followed by determination of the heat transfer coefficient values for your selected Reynolds numbe..

  Calculate the time for the ice to completely melt

If the chest is completely filled with ice, calculate the time for the ice to completely melt. State your assumptions. The enthalpy of fusion for water is 330 kJ/kg.

  Explain what is the amplitude of the response x

In the idealized model attached shown, m = 15 kg, k = 135 N/m, and the viscous damping ratio is 0.15. Assume that an external harmonic force F(t) = 15 cos 4 t acts on the system with F0=15 N and forcing frequency of 4 rad/s.

  Determine the work and heat transfer

determine the work and heat transfer, each in kJ. sketch the process on p-v and T-s coordinates. Associate the work and heat transfer with areas on these diagrams.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd