Calculate the local atmospheric pressure in the city in kpa

Assignment Help Mechanical Engineering
Reference no: EM13623356

1. Write out the differences between:

a) close system and open system;

give one example and state what type of system it is

b) intensive property and extensive property

give one example and state what type of property it is

2. The temperature of ambient air in a certain location is -30oC. Express this temperature in oF, K, and R units.

3. The temperature of water changes by 10R during a process. Express this temperature change in oF, oC and K units.

For the following calculation, take g = 9.8 m/s2.

4. Determine the atmospheric pressure at a location where the barometric reading is 720mmHg, given the specific gravity of mercury to be 13.6.

5. The absolute pressure in water (water density is 1000kg/m3) at a depth of 5 m is read to be 145kPa. Determine (a) the local atmospheric pressure; and (b) the absolute pressure at a depth of 3m in a liquid whose specific gravity is 0.85 at the same location.

6. The pilot of an airplane reads the altitude 8000m and the absolute pressure 25kPa when flying over a city. Calculate the local atmospheric pressure in the city in kPa and in mmHg. Take the densities of air and mercury to be 1.2 kg/m3 and 13600 kg/m3, respectively.

Reference no: EM13623356

Questions Cloud

Also find the laplace transform of the three resulting : determine the system of equations from the following equationsxdot ax buy cx dualso find the laplace transform of
Suppose an investment offers to triple your money in 36 : suppose an investment offers to triple your money in 36 years. what annual rate of return are you being offered if
A market research firm did a report about the residential : a market research firm did a report about the residential telephone numbers in new york state which says 54 of all
The distance between an object and the screen is 256 m a : the distance between an object and the screen is 2.56 m. a converging lens of focal length 25 cm is placed used to cast
Calculate the local atmospheric pressure in the city in kpa : 1. write out the differences betweena close system and open systemgive one example and state what type of system it isb
The drug dozenol is tested on 40 male subjects recruited : the drug dozenol is tested on 40 male subjects recruited from new york and 40 female subjects recruited from
A copper wire of cross-sectional area320 times 10-6 m2 and : a copper wire of cross-sectional area3.20 times 10-6 m2 and length 3.60 m has a current of 2.40 a uniformly distributed
A zoo has offers to look over cost of a new lion den the : a zoo has offers to look over cost of a new lion den. the actual cost y at 200000 is predicted by the pdffx x for 0
A flywheel is a solid disk that rotates about an axis that : a flywheel is a solid disk that rotates about an axis that is perpendicular to the disk at its center. rotating

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the brake kw of the fan and its efficiency is 65

a centrifugal fan is to be used to take a flue gas at rest zero velocity and at a temperature of 352.6k and a pressure

  What force must be applied to the plunger

the pressure in the vein is known as 1850 Pa. what force must be applied to the plunger, so that 1.5 x 10^-6 m^3 of solution can be injected in 5.0 s?

  Steam at 160 bar 480degc enters a two-stage turbine

steam at 160 bar 480degc enters a two-stage turbine operating at steady sate with a volumetricnbspflow rate of 800

  Determine first drawing your schematic and numbering your

a closed feedwater heater of a rankine cycle is used to heat the working fluid water from a state of 370acircdegf

  What is the enthalpy change of the fluid from the initial

a piston cylinder device contains 1 kg of liquid water at 200kpa and 25oc. heat is added to the water in the cylinder

  Specify a diameter d using a design factor of nd

xerted on the shaft shown in the figure, which rotates at 1150 rev/min and supports a 10-kip bending force. Use a 1095 HR steel. Specify a diameter d using a design factor of nd = 1.6 for a life of 3 min. The surfaces are machined.

  At the exit the pressure and velocity are 1800 kpa and 588

steam enters an adiabatic nozzle at 4000 kpa 440oc with a velocity of 75 ms. at the exit the pressure and velocity are

  What type of feedback data should we be collecting

what type of feedback data should we be collecting; in order to make sure that our MPS data, our MRP data, our Aggregate Planning, etc. are all correct?

  The fuel mass flow rate is 60 kgmin assume that the plant

a gas turbine power plants operates using methane as fuel and 200 excess air. fuel and air enter the plant at 25

  Plot the maximum efficiency of a nuclear power plant as a

the environment in a certain area is 15 degrees c. plot the maximum efficiency of a nuclear power plant as a function

  Discuss the factors beyond crystal structure

Discuss the factors beyond crystal structure, quenching and temperature that affect he results of a specimen in a Charpy V notch impact testing.

  These are all serial input parallel latched sinking driver

these include micrel mm5450 mic5821 allegro a6276ea ucn5832a and texas instruments tpic6c595. these are all serial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd