Calculate the line parameters for each line

Assignment Help Mechanical Engineering
Reference no: EM131214823

Application: Coaxial transmission line. Two coaxial transmission lines, each made of an inner and outer shell are given. The radius of the inner shell is a = 10 mm and the radius of the outer shell is b = 20 mm. The lines are shown in cross section in Figure 14.32. Permittivity and permeabilities are given. Calculate:

1821_d86dc9a4-da28-4a14-8aac-05a691f77321.png

(a) The line parameters for each line assuming perfect conductors.

(b) The characteristic impedance and phase velocity of the lines

Reference no: EM131214823

Questions Cloud

Problem regarding the development of the internet : When looking at the chronology of the development of the Internet, which development do you believe to be the most important? Why?
Explore various application software : 1. As you explore various application software, discuss at least one of your preferred application software with the class, why you find the software beneficial, and how your classmates may benefit from the software?
Execute a matlab program to calculate for an arbitrary n : Write and execute a MATLAB program to calculate for an arbitrary n. - What is the largest integer n for which your program gives a finite answer?
Challenges in formatting a document : What might be some challenges in formatting a document? What are the added values in formatting a documenting?
Calculate the line parameters for each line : The lines are shown in cross section in Figure 14.32. Permittivity and permeabilities are given.
Program to evaluate the binomial coefficient : Write your own program to evaluate the binomial coefficient. - What is the largest integer n for which your program gives a finite answer?
Critical task as a project manager : What do you believe is the most critical task as a project manager? What role should they play (a coordinator, a technical advisor, a consultant, a coach, a manager, a bridge between project team, upper manager and customers or a combination of al..
Which are ill defined and tenuously rooted : Discuss a moral dilemma you have either found yourself involved in or one your closely observed another involved in where you or that other person have had to make a decision based solely on your moral beliefs. First, read Chapter 9, p. 375, "Your..
Database design lacks functionality to support theaters : The current movie database design lacks functionality to support theaters and show times.  It is not possible to see what theaters a movie is currently playing in or what movies are being shown at a particular theater.  Therefore, we would like to..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is your estimate of the fluid viscosity

The tube diameter is 2 mm, and the rate of draining is found to be 1.9 cm3 /s. What is your estimate of the fluid viscosity? Is the tube flow laminar?

  Calculate diameter of this steel rod when it is under load

A 1 m steel rod (circular cross-section) has a diameter of 2 cm and is pulled in tension with a load of 50 kN. The steel rod experiences an entirely elastic elongation of 1 mm. a) Calculate the elastic modulus of the steel. b) Calculate the diameter ..

  A pump steadily draws water from a pond at 20 lbs pressure

a pump steadily draws water from a pond at 20 lbs. pressure at the inlet is 14.7 psi the temperature is 68 degrees f

  Gas turbine engine has a pressure ratio

A gas turbine engine has a pressure ratio of 10, and the intake air is at 90 kPa and 280K. Both the compressor and turbine have an isentropic efficiency of 100% and a regenerator with an effectiveness of 0.8 is used. The highest temperature in the cy..

  What is the minimum pressure in psig

For a pump in the basement which must deliver water to a bucket on the floor of the upper mechanical room, what is the minimum pressure in psig you will see at the pump discharge.

  A spur pinion d 100 mm has a torque of 225 nm applied to

a spur pinion d 100 mm has a torque of 225 nm applied to it. for pressure angle of 20 degreea. calculate wt wn and wr

  What value of sp is required

In a tubular low pressure chemical vapor deposition (LPCVD) reactor, gas is introduced at one end at a rate of 75 torr-L/min. At the other end is a vacuum pump of a speed Sp. If the reactor must operate at 1 torr, what value of Sp is required?

  Introduction about nuclear power

This is the question I need to be answered-First of all an introduction about Nuclear Power

  A steel plate which is 15 m by 15 m and 30 mm thick is

a steel plate which is 1.5 m by 1.5 m and 30 mm thick is lifted by four cables attached to its corners that meet at a

  What is the amplitude of the force transmitted to building

Consider a model of a building whose base moves as a result of an earthquake. The building can be modeled as a single-degree-of-freedom spring-mass system where the building mass is lumped on top of two beams used to model the walls of the building.

  An overall balance around part of a plant involves three

an overall balance around part of a plant involves three inlets and two outlets which only contain water. all streams

  Design your circuit using basic gates

Design your circuit using basic gates.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd