Calculate the limestone feed rate lbhr assume that the flow

Assignment Help Mechanical Engineering
Reference no: EM13613301

A power plant produces a flue gas with a mass flow rate of 2 million pounds per hour. Of that, 150,000 lb/hr is water vapor, and 15,000 lb/hr is SO2. All the other gases that are not SO2 or water have an average molecular weight of 28.

(a) Calculate the concentration of SO2 in the flue gas in ppm(v) (dry basis). Regulations require that 92% of the SO2 be captured, and a limestone scrubber will be used to do the job. Assume that scrubber exit gases are saturated with water vapor at 125 degrees Fahrenheit.

(b) Estimate the SO2 concentration of the exiting gases in ppm(v) (dry basis). Assume that there is no HCl in the gases, and that the limestone is 96% CaCO3 (with a MW of 100) and 4% inerts. The alkalinity supplied will be 1.12 times the stoichiometric ratio.

(c) Calculate the limestone feed rate, lb/hr. Assume that the flow rate exiting the scrubber is 800,000 acfm and the scrubber pressure drop is 10 in. H2O. Calculate the fan power used just by the scrubber, in hp.

Reference no: EM13613301

Questions Cloud

Assuming that only caso3 is produced calculate the daily : assuming that only caso3 is produced calculate the daily production rate in tonsday of a 55-solids sludge from a
A 154 wide 134 high 1400 car hits a very slick patch of ice : a 1.54 wide 1.34 high 1400 car hits a very slick patch of ice while going 20.0 . air resistance is not negligible. if
What information does calculating standard deviation : 1. what information does calculating standard deviation provide? how is the z-score related to standard deviation?2.
Ignoring taxes when will eps be identical for plan i and ii : blue stripes co. is comparing two different capital structures. plan i would result in 8500 shares of stock and 313500
Calculate the limestone feed rate lbhr assume that the flow : a power plant produces a flue gas with a mass flow rate of 2 million pounds per hour. of that 150000 lbhr is water
The skis have a thrust of 270 n and a coefficient of : sam whose mass is 66 kg takes off across level snow on his jet-powered skis. the skis have a thrust of 270 n and a
Apprx 103 of americans high school students drop out bf : apprx 10.3 of americans high school students drop out bf graduation. choose 10 students entering school at randon find
Four point charges of magnitude 47 microc are at the : four point charges of magnitude 4.7 microc are at the corners of a square of side 3 m. a find the electrostatic
Mountaineers sell its rock-climbing shoes worldwide : mountaineers sell its rock-climbing shoes worldwide. mountaineers expects to sell 4000 pairs of shoes for 165 each in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd