Calculate the length of the conveyor belt shown b calculate

Assignment Help Mechanical Engineering
Reference no: EM13602287

The crate containing 40 bricks sits on a slopped conveyor belt which is used to raise the crate to the next level of the factory at a constant speed. When the conveyor was installed it was determined through safety checks that at an angle of 30o the crate would begin to slip down the slope. a Calculate the length of the conveyor belt shown b Calculate the coefficient of friction between the crates and the conveyor belt.

Reference no: EM13602287

Questions Cloud

Provide two values for each pair of values use a percentage : provide two values. for each pair of values use a percentage to express their relative change or difference. use the
Farnum 1994 discusses a chrome plating process small : farnum 1994 discusses a chrome plating process. small electric currents are run through a chemical plate that contains
Part b if the weightlifter does 23 repetitions a day what : a weightlifter works out at the gym each day. part of her routine is to lie on her back and lift a 41kg barbell
Yashchin 1995 discusses a process for the chemical etching : yashchin 1995 discusses a process for the chemical etching of silicon wafers used in integrated circuits. this process
Calculate the length of the conveyor belt shown b calculate : the crate containing 40 bricks sits on a slopped conveyor belt which is used to raise the crate to the next level of
Kane discusses the concentricity of an engine oil seal : 1. kane discusses the concentricity of an engine oil seal groove. historically the standard deviation for the
A boat travels at a constant speed of 15 ms around the : a boat travels at a constant speed of 15 ms around the circumference of a half circle in a time span of 45 s. what is
What is the required diameter of the model elbow to : the pressure drop between the entrance and exit of a 150 mm diameter 90deg elbow through which ethyl alcohol at 20degc
Consider the following statement each culture has its own : consider the following statement each culture has its own norms of etiquette. in a diverse society like america as well

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A horizontal platform rests on four vertical springs

A horizontal platform rests on four vertical springs, each of stiffness 15kN/m and mass 0.25kg. what will the frequency of oscillation of the table be if it has a mass of 2.okg

  Two blocks a and b are arranged with pulleys as shown block

two blocks a and b are arranged with pulleys as shown. block a has an initial velocity t 0s to the left of va1.2 ms.

  At a location where the local atmospheric pressure is 142

a manometer is connected to a water pipe to measure the pressure at the center of the pipe. the manometer is

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Which acitivities does hydraulic analysis of a pipeline

which acitivities does hydraulic analysis of a pipeline include using HYSYS software? what data can obtained?

  Unidirectional reinforced composites1 calculating the

unidirectional reinforced composites1. calculating the mechanical properties of unidirectionally reinforced composites

  Find the volume rate of ?ow in ab

Find the volume rate of ?ow in AB, the velocity in BC, the velocity in CD and the diameter of CE.

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Determine the magnitude of its acceleration

The car travels up the hill with a speed of v = (0.4s) m/s, where s is in meters, measured from A. Determine the magnitude of its acceleration when it is at point s = 50 m, where p = 500 m.

  What is the skidding time

The mass of one wheel is 125 kg and its radius of gyration is 0.75 m. The radius of a wheel is 1 m.

  Computer programs and other software

Computer programs and other software (including Web Pages like this one). This includes graphics and icons and the like, which may also be "graphic works". OK, my work is on the list. How do I copyright it?

  Using variable specific heat method

1. A Brayton cycle uses air and produces a net work of 14000 Btu/s with an inlet state of 60°F, 14.7 psi and a compression ratio of 16. The heat added in the combustion process is 400 Btu/lbm. If the thermal efficiency is 0.547 Determine: Using va..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd