Calculate the length of action z and the contact ratio mp

Assignment Help Mechanical Engineering
Reference no: EM131166590

Two equal spur gears of 48 teeth mesh together with pitch radii of 96.0 mm and addendums of 4.00 mm. If the pressure angle is 20°, calculate the length of action Z and the contact ratio mp.

Reference no: EM131166590

Questions Cloud

Groups and the current rulemaking process : Given your thoughts on these groups and the current rulemaking process...how might we improve where there are areas where improvement may be warranted? What changes should we make with respect to the rulemaking process? Would you say that the fiel..
How important is a nonprofits financial condition : how important is a nonprofit's financial condition in relation to its mission? Incorporate into your discussion the impact of the Sarbanes-Oxley Act, and the ethics required to address the NPO's fiscal position.
Determine and label angle of approach and recess for pinion : Make a full-size layout of these gears, and label the beginning and end of contact. Determine and label the angle of approach and recess for the pinion.
Groups and the current rulemaking process : Given your thoughts on these groups and the current rulemaking process...how might we improve where there are areas where improvement may be warranted? What changes should we make with respect to the rulemaking process? Would you say that the fiel..
Calculate the length of action z and the contact ratio mp : Two equal spur gears of 48 teeth mesh together with pitch radii of 96.0 mm and addendums of 4.00 mm. If the pressure angle is 20°, calculate the length of action Z and the contact ratio mp.
Explain the process of money market hedge : IBM purchased computer chips from NEC, a Japanese electronics concern, and was billed ¥250 million payable in three months. Currently, the spot exchange rate is ¥111/$ and the three-month forward rate is ¥107/$. Explain the process of a money market ..
Investigate four attacks and provide a short paper : Investigate four attacks and provide a short paper delineating: - The methods and motives associated with each of your selected attacks.
Discuss difference between republican and democratic parties : Discuss two differences between the Republican and Democratic parties that may have an ethical impact (positively or negatively) on the American people.
Improving the quality of care : Elaborate on the major reasons why, according to the text, health care systems can be considered complex. Next, argue a case for double-loop against single-loop learning in organizational learning

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the minimum necessary coefficient

Determine the minimum necessary coefficient of static friction necessary so that the shims will remain in place.

  Determine the net electric output

For a combined turbine-generator efficiency of 83%, determine the net electric output. Disregard the effect of the KE correction factors.

  Calculate the average temperature of the plate surface

Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s over a 1m long flat plate that is heated with a uniform heat flux of 1250 W/m2. Assume the flow is fully turbulent over the length of the plate.

  Specify efficiency of the gear train as a percentage

Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 and determine the input power required at shaft 1.

  A promising method of power generation involves collecting

a promising method of power generation involves collecting and storing solar energy in large artificial lakes a few

  Calculate the corresponding z transform when u(t) is

Write down an expression for uk, the general term of the sequence, and calculate the corresponding z transform when u(t) is

  Heat transfer to the air in the heating section

Air at 14.7 psia, 50oF, and 60% relative humidity is first heated to 72  o F in a heating section and then humidified by introducing water vapor. The air leaves the humidifying section at 75oF and 55% relative humidity.

  Temperature rise of the river far downstream of the plant

It is proposed to build a one million kW electric power plant with steam as the working fluid. The condensers are to be cooled with river water at a flow rate of 5 x 108 lbm/hr. The maximum steam temperature will be 1000 F and the pressure in the con..

  Superheated water at 180 psi and 500 degf is allowed to

superheated water at 180 psi and 500 degf is allowed to cool at constant volume until the temperature drops to 250

  The emissivity of a person is 095 and the heat transfer

if you are standing in a room that is held at a constant 75 f and your body temperature remains at a constant 98.6 f

  Calculate the path length of the cell

Calculate the path length of the cell.

  At what time does the hour hand point in the same direction

a clock face has negative point charges -q -2q -3q middot middot middot -12q fixed at the positions of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd