Calculate the instantaneous oxidation rate ms and mmyear at

Assignment Help Mechanical Engineering
Reference no: EM13625775

Consider oxidation of a metal plate (half-thickness, x_0= 0.02m). After 800hours = 2.88E6 seconds at 900 C, the oxide layer thickness is 0.0005m. Assume the diffusion controlled quasi- steady state model.

a) calculate the (instantaneous) oxidation rate (m/s and mm/year) at t = 800hours. (t from the onset of oxidation)

b) calculate the time required for the oxide layer to grow from 0 m thick at t=0 to 0.002m thick.

Reference no: EM13625775

Questions Cloud

Use a normal approximation to find the probability of the : use a normal approximation to find the probability of the indicated number of voters. in this case assume that 145
Aluminum-copper alloy96 atom al 4 atom cu is : aluminum-copper alloy96 atom al 4 atom cu is solution-annealed at 550c and then aged at 450c. at 450c a cual2
They then report the probability of getting six heads or : a student creates a simulation that flips a coin 200 times in a row randomly generates 0s and 1s recording whether or
Explain the concept and application of uniform : explain the concept and application of uniform
Calculate the instantaneous oxidation rate ms and mmyear at : consider oxidation of a metal plate half-thickness x0 0.02m. after 800hours 2.88e6 seconds at 900 c the oxide layer
A 40 foot long aluminum street lighting support is sized : a 40 foot long aluminum street lighting support is sized and welded into position between two very large bridge beams
In the sample the mean score is 64 points and the standard : a simple random sample of 20 third-grade children from a certain school district is selected and each is given a test
Using visible light with a vacuum wavelength of 559 nm what : astronomers have discovered a planetary system orbiting a star which is at a distance of 5.6 times 1018 m from the
A steam power plant operates on a rankine cycle with reheat : a steam power plant operates on a rankine cycle with reheat. steam enters the turbine at 600 psia and 700 f. steam is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The entrance is square edged calculate the flow rate if the

water flows from a storage tank through a horizontal 6-inch pipe cast iron and discharges water 20 degrees celsius into

  The compressor is cooled by the ambient air at 15 degc at

air enters a compressor at ambient conditions of 100kpa and 17 degc with a low velocity and exits at 1mpa 327 degc and

  Find the entropy in a throttling process per unit mass for

find the entropy in a throttling process per unit mass for ammonia. take the inlet state as specified as saturated

  Review the logic used to develop brake systems of the motor

review the logic used to develop brake systems of the motor vehicle historically. make critical analysis of each phase

  The upstream flow mach number is 24 calculate the

consider an oblique shock wave with a wave angle of 30 degree. the upstream flow mach number is 2.4 calculate the

  It bums in a steam generator with 115 percent theoretical

a gaseous fuel has the following volumetric analysis 90 methane ch4 5.0 ethane c2h6 and 5nitrogen. it bums in a steam

  Define two infinite parallel plates are separated

Two infinite parallel plates are separated by a distance h. The space between them is filled with a Newtonian fluid: density (rho), viscosity (mu). The lower plate is fixed

  Determine the optimal pressures

determine the optimal pressures, temperatures, and fraction of steam extracted to maximize thermal efficiency.

  A person with a receiver is 5 km away from the transmitter

a person with a receiver is 5 km away from the transmitter .what is the distance that this person must move further to

  The air is first expanded isothermically to 500kpa then

a piston-cylinder device contains 0.15kg of air initially at 2 mpa and 350 degrees celsius. the air is first expanded

  Starting with the general form of conduction equation in

consider a cylinder with an inner radius of r1 and an outer radius of r2 and constant thermal conductivity k. heat is

  What is the best approach to learn programming directed

What is the best approach to learn programming directed towards numerical methods and CFD for a beginner.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd