Calculate the frequency ratio the damping ratiofactor the

Assignment Help Mechanical Engineering
Reference no: EM13639736

In a single degree of freedom vibrating system, the concentrated mas which weighs 38.6 lbs. is acted upon by a disturbing force f(t)=50sin(20pi*t). If the spring constant is 400 lb./in. and the damping coefficient is 4 lb-sec/in, calculate the frequency ratio, the damping ratio(factor), the lag angle, the amplitude of the vibration, and the maximum force transmitted to the foundation.

Reference no: EM13639736

Questions Cloud

The working substance of an engine is 100 mol of a diatomic : the working substance of an engine is 1.00 mol of a diatomic ideal gas. the engine operates in a cycle consisting of
If you were to heat a 30 at ni composition a 50 at ni : a. do the hume-rothery rules suggest this type of solid solution behavior and discuss why or why not.b. at 1000oc what
A heat engine absorbs 120 j of heat from the hot reservoir : a heat engine absorbs 120 j of heat from the hot reservoir and releases 60 j of heat to the cold reservoir during each
The performance of quality inspectors affects both the : the performance of quality inspectors affects both the quality of outgoing products and the cost the products. a
Calculate the frequency ratio the damping ratiofactor the : in a single degree of freedom vibrating system the concentrated mas which weighs 38.6 lbs. is acted upon by a
A mixture of propane and butane is fed into a furnace where : a mixture of propane and butane is fed into a furnace where it is mixed with air. the furnace exhaust leaves the
Snowballs are thrown with a speed of 18 ms from a roof 90 m : snowballs are thrown with a speed of 18 ms from a roof 9.0 m above the ground. snowball a is thrown straight downward
How do you calculate the effective temperature of jupiter : how do you calculate the effective temperature of jupiter if the sun is its only source of heat given that jupiter is
Validate your feht model by comparing predictions with the : a straight fin of uniform cross section is fabricated from a material of thermal conductivity k 5 wmk thickness w 20

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Water flowing from the oscillating slit produces a velocity

water flowing from the oscillating slit produces a velocity field givin by vuosinwt-yvoi voj where uo vo and w are

  Calculate the head provided by the pump

Calculate the head provided by the pump and Calculate the brake power required if the pump efficiency is 75% (kW).

  The input conditions are 10c and 379 kpa what are the

a water heater operating under steady-flow conditions delivers 10 litersmin at 75 c and 370 kpa. the input conditions

  The mass of the steam is 12 lb find the work in btu and the

steam in a piston cylinder assembly undergoes a polytropic process with n2 from an initial state of p500 psi v11.7

  Determine the change in specific entropy between states 1

determine the change in specific entropy between states 1 and 2 of the fluids given belowa r-134a. state 1 t10c p1 4.1

  Express this compressor work rate in kilowatts and

a heat pump with the elements shown in figure 7.25 condenser to valve to evaporator to compressor to condenser is to be

  Find the variation of vapor temperature and phase interface

a liquid-vapor phase change process in microgravity conditions is carried out sufficiently slowly so that a one

  What is the initial temperature of the water

A piston-cylinder device contains 0.005 m3 of liquid water and 0.9 m3 of water vapor in equilibrium at 600 kPa. Heat is transferred at constant pressure until the temperature reaches 200°C.

  Determine the velocities of the spheres immediately after

sphere a has a mass of 23 kg and a radius of 75 mm while sphere b has a mass of 4 kg and a radius of 50 mm. if the

  How is diffusion time related to diffusion temperature

how is diffusion time related to diffusion temperature for the case where the concentration at some distance into an

  Determine the instantaneous center of rotation

determine (a) the instantaneous center of rotation of the double pulley (b) the velocity of th slider block (c) the number of inches of cord wrapped or unwrapped on each pulley per second.

  An airplane flies horizontally at 550 ms its

an airplane flies horizontally at 55.0 ms. its propellernbspdelivers 1500 n of thrust forward force to overcome

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd