User Account

All Pages

Calculate the force required in direct extrusion of 1100-o

Assignment Help Mechanical Engineering
Reference no: EM13346288

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation. 

Reference no: EM13346288

Questions Cloud

Explain how alkenearomatic c-h stretches are distinguished : explain how alkenearomatic c-h stretches are distinguished from alkane c-h stretches. do the c-h stretch peaks in the
The load is being lifted upward at a constant rate of 9 ms : the load is being lifted upward at a constant rate of 9 ms relative to the crane boom ab. at the instant shown the boom
Assume that a reaction takes place at 295 k and 305 k what : the rate constant of some reaction double with 10 degree rise in temperature. assume that a reaction takes place at 295
Open a new file and create a ladder program to control a : open a new file and create a ladder program to control a washing machine. this washing machine would have a fill
Calculate the force required in direct extrusion of 1100-o : calculate the force required in direct extrusion of 1100-o aluminum from a diameternbspof 6 in. to 2 in. assume that
Consider the following unbalanced reaction what mass of f2 : consider the following unbalanced reaction.p4s f2g pf3gwhat mass of f2 is needed to produce 175 g of pf3 if the
If the vinegar were measured volumetrically eg a pipet what : a. in determining the percent acetic acid in vinegar the mass of each vinegar sample is measured rather than the
A control system is needed to control a small shopping : a control system is needed to control a small shopping center parking lot lighting system and the exterior lighting
A 40-mph wind below past your house speeds up as it flows : a 40-mph wind below past your house speeds up as it flows up and over the roof.nbspif the elevation effects are

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Draw and label a process flowchart

Propane gas enters a continuous adiabatic heat exchanger' at 40°C and 250 kPa and exits at 240°C superheated steam at 300°C and 5.0 bar enters the exchanger flowing counter currently to the propane and exits as a saturated liquid at the same press..

  Landing gear system structural design

Problem Statement Consider the landing gear shown below. Working in teprns of two, come up with a single optimized design for given operational conditions and design considerations

  Find the power being transmitted

As the hollow steel (G = 77 GPa) shaft shown rotates at 180 rpm, a stroboscopic measurement indicates that the angle of twist of the shaft is 3°. Determine

  Determine the pressure in the evaporator

Describe IN DETAIL how you could determine the required rate of heat addition or removal.

  Determine the maximum torque t

a shaft is made of a steel alloy having an allowable shear stress of 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1 in. diameter hole is bored thr..

  Determine the coordinates xc and yc of the point

determine the coordinates xc and yc of the point where the resultant load must act in order to produce uniform normal stress in the column.

  After pumping stops and a new equilibrium is reached the

after pumping stops and a new equilibrium is reached the tire pressure is 600 kp a and the air temperature in the tire

  Calculate how much payload this assembly

The nominal breaking strength of the rope is 10,000 lbs. Calculate how much payload this assembly can allowably pick up. Show your work.

  Explain a gear blank has been successfully hot forged

A gear blank has been successfully hot forged on a mechanical press in a closed die. At the beginning of a new production run

  The transverse shear v at a certain section of timber beam

the transverse shear v at a certain section of timber beam is 25kn. if the beam has the cross sectio shown in the

  Determine the final temperature

determine the final temperature °R, and the final pressure in lbf/in^2. Rair = 53.33 ft·lbf/lb·°R. Assume ideal gas behavior and solve problem using.

  Find the steady-state temperature of the wire

Verify that heating the wire may be treated as a lumped-capacity process, find the steady-state temperature of the wire and find how long it takes for the temperature of the wire to reach 100°C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd