Calculate the db level at one-half the critical frequency

Assignment Help Electrical Engineering
Reference no: EM13263332

Sketch a Bode plot for the frequency response of a High-pass R-C filter where R=470ohms and C=0.047uF. Draw the circuit, calculate the actual cutoff frequency, and calculate the dB level at one-half the critical frequency and twice the critical frequency.

Reference no: EM13263332

Questions Cloud

How is the equilibrium interest rate determined in the bond : How is the equilibrium interest rate determined in the bond market?
How high will the water column stand on the barometer tube : Suppose atmospheric pressure at Denver is 1.0135 × 105 N/m2 today. How high will the water column stand on the barometer tube
Calculate total fees you will pay on this loan commitment : A loan commitment of $4.29 million has an up-front fee of 50 basis points and a back-end fee of 25 basis points. The take down on the loan is 60 percent. Calculate the total fees you will pay on this loan commitment. (Round your answer to 2 decima..
How large is the image of the pear : A pear of 10.2 cm height is placed at a distance of 20.1 m in front of a lens that has a focal length of 26 mm. How large is the image of the pear
Calculate the db level at one-half the critical frequency : Sketch a Bode plot for the frequency response of a High-pass R-C filter where R=470ohms and C=0.047uF. Draw the circuit, calculate the actual cutoff frequency, and calculate the dB level at one-half the critical frequency and twice the critical fr..
What is the weighted average contribution margin : Lambardi sells in a mix of 2 units of A, 3 units of B and 5 units of C. What is the weighted average contribution margin per unit for Lambardi?
Explain about autosomal recessive disorders : Choose one or more of the following and give a definition and a few examples: autosomal recessive disorders, autosomal dominate disorders, x-linked traits, x-linked recessive disorders.
What is the intensity of the beam : An ideal polarizer with its transmission axis rotated 30.5 to the vertical is placed in a beam of unpolarized light of intensity 10 W/m ^2. After passing through the polarizer, what is the intensity of the beam
What will be the level of expected eps : The firm is considering switching to a 25-percent-debt capital structure, and has determined that it would have to pay an 8 percent yield on perpetual debt in either event. What will be the level of expected EPS if the firm switches to the propose..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What are the exact form of the equations

What are the exact form of the equations for the 2nd-order step response for the underdamped, critically-damped, and overdamped conditions.

  Calculate the series impedance and the shunt admittance

A 300-km bundled 500-kV, 60-Hz, three-phase completely transposed overhead line has three ACSR 1351-kcmil conductors per bundle, with the bundle spacing 0.5 m. The horizontal phase spacings between bundle centers are 10, 10, and 20 m.

  Determine the current drawn from a three-phase line

Determine the current drawn from a three-phase 440 V line by a three-phase 15-hp motor operating at full load, 90% efficiency, and 80% power-factor lagging. Find the values of P and Q drawn from the line. (Hint: 1hp = 746W)

  Design a sequential circuit with three d-type flip-flops

A sequential circuit with three D-type flip-flops Y1Y2Y3, input X and output Z is defined with the following input/output functions: D 1 = X Y 3 + X Y 1 Y 3 D 2 = X  ( Y  3 + Y 2 ) + X Y 2 Y 3 D 3 = X Y 3 + Y 2 Y 3 Z = Y3

  Derive minimal boolean expressions for circuit outputs

Design a 2-bit counter that, when f = 1, counts in the repeating sequence: 0, 2, 3, and when f = 0, counts in the reverse direction. Use T flip-flops. (a) Construct a state diagram or state table.

  Determine the maximum gain of the antenna

A single-turn resonant circular loop with a /8 radius is made of copper wire with a wire radius of 10^4 pi f/2 and conductivity of 5.7 × 10^7S/m. For a frequency of 100 MHz, determine, assuming uniform current

  Estimate the output current of a one square meter panel

The total sunlight at noon on a clear summer day is just over 1KW/m^2. Assuming a solar panel with 20% efficiency, and an output voltage of 20V, estimate the output current of a one square meter panel in full sunlight.

  What is initial value if the overhead values were considered

write an 8051 program that would generate a 200khz, 50% duty cycle, square wave at P1.0.Use Timer 0 for the delay. Ignore the overheads cycles due to the instructions in the loop. Assume 12 MHz clock. All data must be hex.

  Find the slopes and the interceptions at the voltage axis

An abrupt p-n junction has a doping concentration of 1015, 1016, or 1017 cm-3 on the lightly doped n-side and of 1019 cm-3 on the heavily doped p-side. Obtain series of curves of 1/C2 versus V, where V ranges from -4 to 0V in steps of 0.5V.

  Determine ratio of open-circuit voltage to built-in barrier

Solar Cell Consider a GaAs PN junction solar cell with the following parameters. Na=10^17 cm^-3, Nd= 2*10^16 cm^-3, Dn=190 cm^2/s, Dp=10 cm^2/s, Tn0=10^-7s, and Tp0=10^-8s.

  Calculate the gain and bandwidth after the feedback

Single pole amp. has an open loop gain 10^6 and open loop bandwidth of 10Hz. If the feedback factor =1, calculate the gain and bandwidth after the feedback

  Calculate the energy generated by the electric machine

a. The mass of an electric car is 900 kg including the passengers. A single motor mounted on the front wheels drives the car, and the radius of the wheel is 0.3 m. The car is going downhill at a speed of 50 km/hr, and the slope of the hill is 30 d..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd