Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 6-pole, 3-phase, 50 Hz synchronous motor is supplied from 6.6 kV busbars. Its opencircuit voltage is 3.3 kV/phase. The per phase resistance and synchronous reactance are 0.6 Ω and 4.8 Ω respectively. Calculate the current, power factor and torque developed, when the excitation emf lags the busbar voltage by 15°, 25°, and 35° (elect).
How high of a signal source impedance can exist and still provide an output signal from an inverting amplifier circuit. What effect would the signal source impedance have on the non-inverting amplifier.
Discuss the importance of electrical isolation when interfacing microcontrollers to higher voltage inductive circuits (motors). Include detail of how electrical isolation can be achieved to protect the microcontroller and motor.
The total sunlight at noon on a clear summer day is just over 1KW/m^2. Assuming a solar panel with 20% efficiency, and an output voltage of 20V, estimate the output current of a one square meter panel in full sunlight.
If the same power is to be supplied to the same consumer by two wire d.c. system by a new line having a total resistance of 0·05 Ω and if the allowable voltage drop is 25%, calculate the d.c. supply voltage.
Two Bit Analog to Digital Converter - MATLAB Let x (t) = 0.8 cos(2*pi*t) + 0.15, 0≤ t ≤ 1, and zero otherwise, be the input to a two bit ADC converter. a.) For a sampling period Ts = 0.025 sec; determine and plot using MATLAB the sampled signal: x (n..
Given the following function: F(W,X,Y,Z) = fm(2,3,5,7,12,13). a. Implement the function using an 8-input multiplexer. b. Implement the function using a 4-input multiplexer.
A load has a 20 ohm resistor and a 4 Henry inductor connected in series. It is connected to a power source with v(t) = 100 cos(50t), connected in series to the load. What is the impedance of the load? Use phasor transform methods to obtain your an..
a single phase 100 kVA, 1000/100 V transformer gives the following test results: Open Circuit test: 100V, 6.0 A and 400 W Short Circuit test: 50V, 100A and 1800W At what load will maximum efficiency occur
Given the following function in product-of-sums form, not necessarily minimized, F(W,X,Y,Z) = (W + X' + Y')(W' + Z')(W + Y), Re-express the function in the canonical sum-of-products form. Use little m notation.
The input, Vin, is differential not single-ended. Design an analog circuit with a transfer function of Vout = 50 Vin + 2.5 powered by a single +5 V supply. You may use any of the analog chips.
In Astable multivibrator (using OP-AMP) and Butterworth 2nd order filter(using OP-AMP)(both high pass & low pass filter), both positive and negative feedback are given. But in Astable mutivibrator positive feedback dominates
A 10 microFarad capacitor is in series with a 100 ohm resistor, a switch, and a 10.0 volt battery. At time t = 0 seconds the switch is closed. What is the current in the resistor at time t = 0.1 microseconds. What is the current in the resistor at ti..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd