Calculate the current in the resistor

Assignment Help Electrical Engineering
Reference no: EM13311545

The voltages at opposite ends of a 470Ω, ±5% resistor are measured as V1 = 12V and V2 = 5V. The measuring accuracy are ±0.5V for V1 and ±2% for V2. Calculate the current in the resistor and specify its accuracy.

Reference no: EM13311545

Questions Cloud

Define the resulting sign of delta g and the spontaneity : Construct a delta H and delta S table, including the four possibilities associated with the two possible signs for each of delta H and delta S. Discuss the resulting sign of delta G and the spontaneity of the process.
Project to develop a controller for a new satellite : Project to develop a controller for a new satellite.
Explain second law states that the entropy of the universe : The second law states that the entropy of the universe (system and surroundings) increases in a spontaneous process : delta Ssyst + delta Ssurr is greater than or equal to 0.
What is the maximum speed you could have : You're driving down the highway late one night at 18 m/s when a deer steps onto the road 45m in front of you. What is the maximum speed you could have
Calculate the current in the resistor : The voltages at opposite ends of a 470Ω, ±5% resistor are measured as V1 = 12V and V2 = 5V. The measuring accuracy are ±0.5V for V1 and ±2% for V2. Calculate the current in the resistor and specify its accuracy.
Find the net torque on the stone about the center of circle : A 6-kg stone is tied to a 0.79-m long string and swung around a circle at a constant angular velocity of 19 rad/s
Explain what is the ratio of enantiomers of 2-octanol : What is the ratio of enantiomers of 2-octanol in the product mixture? 55% (S) and 45% (R). However, I am not sure how to draw the structure of the major enantiomer produced in this reaction. Indicate the configuration of the stereogenic center usi..
The rms value of the line-to-line voltage : Consider a 3 phase 25 kVA, 440 V, 60 Hz ac generator operating at full load (that is, delivering its rated kVA) under balanced steady state conditions. The ac generator has 3 stator windings that output balanced 3 phase voltages. It is usual to..
What is the tangential acceleration of the bob : A pendulum bob of mass m is attached to a massless string of length L. If the bob is released from rest at a horizontal position, What is the tangential acceleration of the bob

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the von mises stress at location of strain gages

A rectangular strain gage rosette attached to an aluminumsurface comprises three identical gages (gage factor = 2.1) ofnominal resistance 200 ohms are each connected into a Wheat stonebridge having 3 other resistance values also of 200 ohms.

  What is the temperture when the output voltage

An intergrated circuit temperature probe is rated at 0-10 volts dc over a 0-175 degrees Celsius range. What is the temperture when the output voltage is 3.65 volts dc

  Find the response of the system if x is equal to u

A causal discrete LTI system is described by y(n)-3/4 y(n-1)+1/8 y(n-2)=x(n) where x(n) is the input and y(n) is the output Find the response of the system if x(n) =u(n)

  Find values of r and x and the supply voltage v

A load consists of a resistance R in parallel with a capacitor of reactance X. The load is fed from a single phase supply through a line of impedance 8.4 + j11.2 ohms. The rms voltage at the load terminal is 1200 at 0 degress V rms,

  Design a circuit to control taillights of ford thunderbird

The state machine has two inputsignals, LEFT and RIGHT, that carry the driver's request fora left turn or a right turn. It also has anemergency flasher input, HAZ, that requires the tail lights to beoperating in hazard mode - all six lights flashi..

  Write a main program to call a procedure

Write a main program to call a procedure that converts the Fahrenheit temperature value stored in the location labeled TdegF to its Celsius equivalent. The range of temperatures is 32F to 212F. The procedure stores the converted temperature in loc..

  Determine the minimum value of transmitter power required

An analog system requires an antenna signal power of 100pW to meet the required detected signal-to-noise ratio. Other system parameters are given as follows: Gt(dB) =4dB determine the minimum value of the transmitter power required.

  Is the sequential circuit a moore model or a mealy model

A sequential circuit with two D flip-flops, A and B; two inputs x and y; one output z; is specified by the following next-state and output equations: A(t 1) = x' y x A B(t 1) = x' B x A Z = B a) Draw a logic diagram of the circuit.

  Define design a synchronous counter using j-k flip-flops

Design of sync counter 0010 to 1101 using JK flip flops, Design a synchronous counter using J-K flip-flops that will count from 0010 to 1101 repetitively.

  Calculate the length of the blades of a 1 mw wind turbine

(a) Calculate the length of the blades of a 1 MW wind turbine. Assume the air density is 1.0 kg/m^3, average wind speed is 15 m/sec, and overall efficiency is 25%. (b) An ideal solar cell is operating at30°C. The reverse saturation curren is0.15 mi..

  Determine ratio of open-circuit voltage to built-in barrier

Solar Cell Consider a GaAs PN junction solar cell with the following parameters. Na=10^17 cm^-3, Nd= 2*10^16 cm^-3, Dn=190 cm^2/s, Dp=10 cm^2/s, Tn0=10^-7s, and Tp0=10^-8s.

  Explain explanation how a parallel rlc filter circuit

Please explanation how a Parallel RLC Filter circuit behave at Low Frequencies, Resonant Frequency and High Frequencies

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd