Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 150-MVA 15/200-kV single-phase power transformer has a 0.018ohm resistance and a 0.075ohm reactance. The magnetizing impedance is j80 per unit.
a.) Find the equivalent circuit referred to the low-voltage side of this transformer.
b.) Calculate the voltage regulation of this transformer for a full-load current at power factor of 0.8 lagging.
c.) Calculate the copper and core losses in transformer at the conditions in (b).
d.) Calculate efficiency.
Calculate the inductive reactance per meter of a single-phase, 50-Hz, two-wire transmission line. Assume each conductor's radius is 9cm and the distance between the two conductors is 5m.
an unknown semiconductor has Eg=1.1ev and Nv=Nc.it is doped with 10^15 donors,where the donor level is 0.2ev below Ec. given that Ef is 0.25ev below Ec, calculate ni and the concentration of electrons and holes in the semiconductor at 300k.
At the end, the wave totally reflects with a pi phase shift, and the reflected wave now interferes with the incident wave to yield a standing wave pattern over the line length.a) Determine the standing wave pattern for the voltage in the line.
Determine the left triceps muscle force (Ftri), elbow joint reaction force (Rj) required to hold this position along with any ground reaction forces (Rg) and/or reaction moments (Mg) in the hand. Show all necessary free body diagrams along with th..
A. find the sixtieth percentile B. Find the seventy fifth percentile C. Determine the number of data points that fall between the sixieth and seventy fifth percentiles you found in parts A. and B.
What would the effect of boundaries be on the diffusivity of a substance (e.g., if you have diffusion of a substance in a pipe, what would the effect of the pipe's walls be on the diffusivity
design a resonance circuit with following specifications: L = 10 mH, RL = 4W, Imax = 200 mA, fs = 10kHz, Q = 20. That is, determine the required R, C, and supply Voltage E. For R and C, use the closest standard values.
Consider a regenerative Rankine cycle with a 600C and 4-MPa throttle, a 5-kPa condenser, and an open feedwater heater at 500 kPa. Turbine efficiencies are 85%. (a) Draw labeled, coordinated T-s and flow diagrams.
Bit 4 of Port B is connected to a switch that normally outputs a zero. Monitor this switch to detect a change from zero to one. Immediately when it becomes one, call a function to toggle Bit 5 of Port B, which is connected to an LED
Given a course voltage of 10V, a source resistance of 10 ohms, a 10mH inductor, and a 5nF capacitor, choose a load resistance and draw a circuit that will have an underdamped (decaying sine wave) second order transient response.
Assume R1 = 1 M-ohm, R2 = 3 M-ohm, and C = 1.5 F. Also take the initial voltage across the capacitance to be VC(0) = 4 V. The voltage source VS has a voltage of 9 etV. The switch is closed at time t=0.
2. Compute the symbol error probability for both constellations in terms of the Gaussian error integral Q(x). 3. Compute the bit error probability for both constellations in terms of the Gaussian error integral.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd