User Account

All Pages

Calculate the common-mode gain and the cmrr

Assignment Help Electrical Engineering
Reference no: EM131085169

A differential amplifier has an open-loop voltage gain of 120 and a common input signal of 3.0 V to both terminals. An output signal of 24 mV results. Calculate the common-mode gain and the CMRR.

Reference no: EM131085169

Questions Cloud

How many full clicks of a single group handle : How many full clicks of a single group handle and how many full clicks of a double group handle are generally used to dose coffee into a port a filter
Draw the complete phasor diagram : A balanced, three-wire, star-connected, 3-phase load has a phase voltage of 240 V, a line current of 5 A and a lagging power factor of 0.966. Draw the complete phasor diagram
After application of the input : A steady voltage of 0.75V is applied to an op amp integrator having component values of R = 200 k and C =2.5 μF. Assuming that the initial capacitor charge is zero, determine the value of the output voltage 100 ms after application of the input.
What other factors do you think affect tuition elasticity : A 1998 study indicated that the price elasticity of demand for four-year university was .67. Using this estimate, how would a 10% increase in tuition at a four-year university change expected enrollments? Do you think the price elasticity of demand w..
Calculate the common-mode gain and the cmrr : A differential amplifier has an open-loop voltage gain of 120 and a common input signal of 3.0 V to both terminals. An output signal of 24 mV results. Calculate the common-mode gain and the CMRR.
Current flowing in the circuit : An inductor has a negligible resistance and an inductance of 200 mH and is connected in series with a 1 k resistor to a 24 V, d.c. supply. Determine the time constant of the circuit and the steady-state value of the current flowing in the circuit.
Calculate the maximum height reached by the second : calculate the maximum height reached by the second stage after burnout.
Resistance determine the magnitude : Determine the minimum value of load resistance so that the voltage gain is not more than 3.0 dB down on the open-circuit value. With this value of load resistance determine the magnitude of the output signal voltage when the input signal is 1.0 mV..
Magnitude of the output signal voltage : Determine the magnitude of the output signal voltage and the signal power in the load when the input signal is 10 mV.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Which direction to simplify resistance for thevenin r

In step four of this problem, how do you know in which direction to simplify the resistance for the thevenin resistance. (since you come up with a different answer depending on which direction you choose to simplify from)

  Calculate the voltage and current ratings of thyristors

A controlled three-phase six-pulse AC/DC converter is supplied with 60 Hz voltage of the line-to-ground RMS value U = 240 V with the output current ideally filtered by an inductor. The maximum DC power of the converter (Pd)max = 50 kW.

  Design a state variable two-pole band-pass filter

Design a state variable two-pole band-pass filter with a geometric center frequency of 2KHz and a 3dB bandwidth of 20 Hz and the tuning resistances need to be 10Kohms each.

  Find minimum pos with inversion and de morgans laws

c) Write the SOP boolean equations as obtained directly from the partial truth table above and sketch a logic circuit diagram for them. d) Reduce the above equations step-by-step into the simplest form that would use only NAND gates.

  Calculate the diode current for the forward bias

A pn-junction is uniformly doped and has dopant concentration of NA = 4 x10^16 cm^-3 in the pregion at 300K. At zero bias, 20% of the total space charge region (W) is extended in the pregion. Calculate Vbi, ND, W, xn and xp.

  For a mos structure with p-type silicon sketch the

for a mos structure with p-type silicon sketch the locations of the charge carriers during depletion. you can

  Find when does computer a retransmit the message

The messages being sent are 2 milliseconds long. Computer A starts sending a message on the bus; 250 microseconds later, Computer B starts to send a message, and 250 microseconds after that, Computer C starts to send a message.

  Calculate modulation index for the fm wave

The carrier wave of frequency 100 MHz is frequency modulated by a sinusoidal wave of amplitude 20 V and frequency 100 kHz. The frequency sensitivity kf = 25 kHz/V. 1. Write expression for FM modulated wave s(t) if Ac = 1 V.

  Network analysis need answer for q1q2 and q10 asap in one

need answer for q1q2 and q10 asap in one hour ltbrgt ltbrgt ltbrgt ltbrgt ltbrgt ltbrgt ltbrgt ltbrgt ltbrgt ltbrgt

  What is the power dissipated through radiation by filament

It is heated to 2500 degrees Celsius in an environment with a temperature of 25 degrees Celsius.

  Derive a suitable sequential circuit

A sequential circuit has two inputs w 1 and w 2 , and an output, z. Derive a suitable circuit for the given condition.

  Determine initial symmetrical rms line and neutral currents

A 10 MVA, 6.9 KV. star connected generator has positive, negative and zero sequence reactance of 25, 20 and 7% respectively. An inductive reactor with 6% reactance based on the rating of the generator is placed in the line from neutral to ground.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd