Calculate the angle between the wires

Assignment Help Mechanical Engineering
Reference no: EM13217073

A gymnast of weight 720N is holding himself in the cross position on the high rings. He is quite still. Draw a free-body force diagram for the gymnast, showing the two upward pulls of the rings on his hands, each of size 380N. Calculate the angle between the wires supporting the rings and the vertical.

Reference no: EM13217073

Questions Cloud

Determine the braking force applied by the breaks : a fully loaded lorry has a mass of 10 tonnes and is travelling along a road at uniform velocity when the brakes are applied and the lorry is brought to rest. if the deceleration is 2m/s2 and the coefficient of rolling friction is 0.15, determine t..
Could the company be found guilty of motor vehicle homicide : The state charged the Todesca corporation with motor vehicle homicide, and the jury found the company guilty. The trial judge imposed a fine-of $2,500. The court of appeals reversed the conviction, and the prosecution appealed to the state's highe..
What is the initial velocity of block b : What is the initial velocity of Block B, constant acceleration of Block A, velocities of both blocks at t=3s, and the total distance traveled by block B from t=0s to t=3s?
Intensive and selective levels of distribution intensity : Identify the difference between intensive, exclusive, and selective levels of distribution intensity? Give an example of a product that would be best for each level of distribution.
Calculate the angle between the wires : showing the two upward pulls of the rings on his hands, each of size 380N. Calculate the angle between the wires supporting the rings and the vertical.
Determine the natural frecuency of the automobile : an automobile having a mass of 2000 kg deflects its suspension springs 0.02 m under static conditions. Determine the natural frecuency of the automobile in the vertical direction by assuming dumping to be negligible.
Determine the speed of the collar : the 2-kg collar is released from rest at A and travels along the smooth vertical guide. determine the speed of the collar when it reaches position B.Also ,find the normal force exerted on the collar at this position.the spring has an unstrectched ..
Explain employees in a less developed country : Respond to the question Is it morally sufficient for a U.S. company to comply with the laws of the foreign country in which it operates? Why or why not? What guidelines should a multinational use to determine a fair wage to its employees in a less..
Calculate the tensile stress required to cause yielding : if the critical resolved shear stress for yielding in aluminum is 240kpa. calculate the tensile stress required to cause yielding when the tensile axis is [001]

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A bullet is fired horizontally into a wood block resting

A bullet is fired horizontally into a wood block resting on a horizontal, frictionless surface. If the mass of the bullet is 0.02 Kg and the velocity is 600 m/s

  Module fea - finite element analysis

Module FEA - FINITE ELEMENT ANALYSIS ,  Provide answers to all questions. Note that assignment part 2 carries 60% of the marks for the course.

  Calculate how far from the fulcrum the tweezer

Using static equilibrium calculations, calculate how far from the fulcrum the tweezers must be held to avoid damaging the sliver.

  Find out the exit temperature

Determining the Exit Temperature and Power Input of Air through a Compressor, Air at 150Pa and 310K enters a compressor of inlet diameter 2cm. The Compressor raises the pressure to 3.5 times the inlet pressure

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  What is the length of the slope of the ramp

Using the knon height and calculated base lenghth, what is the length of the slope of the ramp.

  Determine isentropic efficiency of the compressor

Carbon dioxide enters an adiabatic compressor at 100kPa and 300K at a rate of 0.5kg/s and exits at 600kPa and 450K. Considering constant specific heat, determine (a) isentropic efficiency of the compressor (b) the rate of entropy change in (kW/K) ..

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

  Find the angular velocity of link cd

(a) Find the angular velocity of link CD and the velocity of the pin relative to the slot in link CD. (b) Find the angular acceleration of link CD and the acceleration of the pin relative to the slot in link CD.

  Computation of percentage heat reduction

Calculation of percentage heat reduction, Water at 90 C flows through a 50mm bore steel pipe of wall thickness 8 mm. Ambient temperature is 18 C. Calculate the heat loss per metre length of pipe

  Create a cad model of the planar robot

Create a CAD model of the planar robot

  Explain feasibility

Determining Feasibility, At steady state, a new power cycle is claimed by its inventor to develop 6 horsepower for a heat addition rate of 400 Btu/min

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd