Calculate the actual power transmitted to the second pulley

Assignment Help Mechanical Engineering
Reference no: EM131861986

Question 1. A pulley 150 mm diameter is driven directly by an electric motor at 250 revs min-1. A V-belt is used to transmit power from this pulley to a second pulley 400 mm diameter against a load of 200 Nm.

The distance between the centre of the pulleys is 600 mm, the included angle of the pulley groove = 40°, the coefficient of friction between the belt and pulley is 0.4 and the ultimate strength of the belt is 8 kN.

(a) Calculate the actual power transmitted to the second pulley.

(b) Calculate the power which can be transmitted if the maximum tension in the belt is limited to half of the ultimate strength of the belt.

(c) What would be the effect of the following factors on the maximum power which can be transmitted (give reasons for your answer):

increasing the coefficient of friction
(ii) increasing the included angle of the pulley groove.

(d) What would be the effect on the following if the load torque is increased and the speed maintains constant (give reasons for your answer):

(i) the tension in the tight side of the belt
(ii) the tension in the slack side of the belt
(iii) the power transmitted.

Question 2. A gear train is to be designed to transmit power from shaft 1 to shaft 2 with the following condition:

(i) Shaft 1 (driven by an electric motor) rotates at 100 revs min-1.

(ii) Shaft 2 is to rotate at 400 revs mint in the opposite direction to shaft 1 against a load of 200 Nm.

(iii) The centre of shaft 1 is 300 mm from shaft 2.

(iv) The minimum number of teeth on any gear is 15, all gears must have a multiple of 5 teeth and have a module of 2 mm.

(v) The maximum number of gears permissible is 4 gears and the diameter of the maximum gear must be minimised.

(vi) The centres of the gears should lie on a line which is as close to straight as possible.

(vii) All shafts have a frictional resistance of 5 Nm. Carry out the following:

(a) Design a gear train which satisfies the above criteria. Use a sketch to illustrate your design, label the gears A, B, C, etc. from the driver to the driven gear, and state the number of teeth on each gear.

(b) Determine the input power required at shaft 1.

(c) Specify the efficiency of the gear train as a percentage.

(d) Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 (all other factors remaining constant).

Verified Expert

This assignment presents some important concepts of machine design.In it,some practical questions have been considered related to the pulley and the gear trains,i.e. the important applications on how to transmit power from 1 body to the another body with maximum mechanical efficiency .

Reference no: EM131861986

Questions Cloud

Discuss the difference between a job and a career : Discuss the difference between a job and a career. Discuss the benefits of a mentoring relationship. Explore the impact of work-related stress.
Target debt-equity ratio : Miller Manufacturing has a target debt-equity ratio of .50. Its cost of equity is 15 percent, and its cost of debt is 4 percent.
What is the cost of equity : Clifford, Inc., has a target debt-equity ratio of .85. Its WACC is 8.1 percent, and the tax rate is 35 percent. a. If the company's cost of equity is 11.
Million shares of common stock outstanding : The current share price is $84, and the book value per share is $11. The company also has two bond issues outstanding.
Calculate the actual power transmitted to the second pulley : Calculate the actual power transmitted to the second pulley and Calculate the power which can be transmitted if the maximum tension in the belt is limited
How your officers can use kohlbergs stages of moral : Thoroughly illustrated two to three (2-3) ways in which you would address self-interest and pursuit of pleasure to prevent police corruption.
Identify expected outcomes and the healthcare consumers goal : Identify expected outcomes and the healthcare consumer's goals for a plan individualized to the healthcare consumer or to the situation.
What is the company wacc : Its cost of equity is 10.3 percent, and its pretax cost of debt is 6.4 percent. If the tax rate is 35 percent, what is the company's WACC?
How do companies decide on their capital structures : How do companies decide on their capital structures? Do many publicly-traded companies have preferred stocks in their capital structures?

Reviews

urv1861986

12/3/2018 2:06:32 AM

Very Obliged for your help. My solution has been finished and presented beautifully at the university! A great result yielded by this task. Experts team followed the whole rubric guide to complete the task. Thank you very much...

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd