Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The switch in the circuit has been in position a for a long time. At t=0 the switch is moved to position b.
A.Calculate the initial voltage on the capacitor if v = 200V , and i = 1.9mA .
B. Calculate the final voltage on the capacitor.C. Calculate the time constant for t>0
D. Calculate the length of time required for the capacitor voltage to reach zero after the switch is moved to position b.
a) What is the total resistance corresponding to 1kohm, 4kohm, 10kohm, 4.7kohm resistors connected in series b) What is the total resistance corresponding to 10ohm, 100ohm, 1kohm, 10kohm resistors connected in parallel
how the amplifiers should be connected. To proceed, evaluate the two possible connections between source S and load L, namely, SABL and SBAL. Find the voltage gain for each both as a ratio and in decibels. Which amplifier arrangement is best
Suppose that the cost of electrical energy is $0.12 per kilowatt hour and that your electric bill for 30 days is $60 (power usage only, not including other charges or taxes) Assume that the power delivered is constant over the entire 30 days.
A certain pn junction is operating with Vt=26mV and ni=1.08x10^10 electrons/cm^3. The doping concentrations are Na=2x10^15 cm^-3 and Nd=9x10^16cm^-3. The diffusion coefficient are Dn=34cm^2/s and Dp=12cm^2/s.
A cable technician tested the signal-to-noise ratio on the curb as 20 dBm. This means, if the noise power is at 1 mW, then the signal power should be 20 dB higher then that. If the noise power is 20 mW
one question: During each cycle, the velocity v (in mm/s) of a piston is v = 6t - 6t^2, where t is the time (in sec). Find the displacement s of the piston after 0.75 sec if the initial displacement is zero.
1. Find the transfer function 2. Find the Laplace transformation of the output when x(t)=sin(t)u(t) 3.Find the output by taking the inverse Laplace transform of part 2.
Two voltage waves of equal amplitude, V0, and frequency w, propagate in the forward z direction in a lossless transmission line of characteristic impedence Z0. One waves is phase-shifted from the other by \o radians.
Consider the function f(A,B,C,D) = fm(0,1,4,5,8,9,13,14,15) 1. Map the function, and obtain a minimal sum of products cover. 2. Express the sum of products expression for the minimal cover. F (SOP)
Consider an ideal op-amp in inverting amplifier configuration with feedback impedance Rf=7ohms and an input impedance consisting of a series RL: Ri=9ohms and Li=5H. Let h(t) be the impulse response of the overall amplifer.
Write a C program for the 68HCS12 microcontroller to send the pattern 0x55 to byte-sized Memory Location "OUT1" and then call a delay function. The delay function should generate a delay of two milliseconds.
Assume the acceptable deviation is +- 5.8%. Thus, a nominal rms voltage of 120 V will range from 113 to 127 V. Suppose the line to line voltage at Customer A is 13.8kV, the load at customerA consumes complex power (1.2+j1.2)x 10^6 W.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd