Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Because of a wartime shortage of copper, the electromagnets at Oak Ridge National Lab used to separate U-235 isotopes were wound with pure silver (atomic volume 10.3 cc/mole). If 100 meters of silver wire 2 mm in diameter required 8.1 watts when carrying 4 amps of current, calculate for silver the (a) resistivity, (b) mobility, (c) collision time, (d) mean free path, (e) Hall coefficient, and (f) the Hall field in a transverse magnetic field of 9 tesla. Assume silver has one free electron per atom, and a temperature of 300K. (Note: Electrical power equals the product of the current and the voltage or the product of the current squared and the resistance.)
A bandlimited signal with maximum frequency of 3.3 kHz, what is the minimum sampling frequency to sample this signal If a sinusoidal signal of 7 kHz is sampled by this sampling frequency, what is the frequency of the alias.
build a cicuit that must be able to operate a 3 amp load of the LED while being able to operate at voltages around 3V or 6V. It must be able to keep the LED on constantly while also being able to pulse the LED.
A series-connected load draws a current i(t)=4cos(100pt + 10°) A when the applied voltage is v(t) = 120cos(100pt-20°) V. Determine a) The circuit‘s apparent power b) The power factor, pf c) The value of the impedance Z
Write the verilog code for a circuit that counts the number of 1s in a byte. Write the verilog code using a structural approach based on four Half-Adders, two 2-bit adders and one 3-bit adder. Write the test bench code to test the design.
two resistors with nominal values of 4.7K ohm and 10K ohm, are used in a voltage divider with a +15V supply to create a nominal +10V output. Assuming the resistor values to be exact, what is the actual output voltage produced
Assume that the I bit for external hardware interrupt IRQ is enabled and is low-level triggered. Explain how this interrupt works when it is activated. How can we make sure that a single interrupt is not interpreted as multiple interrupts
Assume the factory described in the previous problem is fed from a line having an impedance of 0.02 + j0.16-ohm. The voltage at the factory is maintained at 480 V(rms). Find the average power loss in the line before and after the load is added.
Find the laplace transform of the following functions and the time-shifting property (if needed) of the unilateral Laplacetransform: u(t)-u(t-1)
An inductance of 8 mH is combined in parallel with a capacitance of 1.5 µF. What is the characteristic frequency (Hz) (not radian frequency) of the combination
A pressure measurement system is stated as having the following characteristics. Range: 0 to 140 kPa; Accuracy: ±1.5% of the displayed reading; Temperature sensitivity: ±0.1% of the reading per °C If the instrument indicates a pressure of 120 kPa
Consider the LTI described by the following input-output relation: y[n] = 3/4y[n-1]-1/8y[n-2]+x[n] a)Find system function H(z) and check is system is stable. b)Determine impluse response h[n] of system
A 2000kW synchronous motor operates at a three - phase line-to-line voltage of 4kV. It has a synchronous reactance of 4 ohms per phase. Calculate a) The nominal full load current of the machine when the excitation voltage E0 ( line - to-line) is 4k..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd